/dev/sda === START OF INFORMATION SECTION === Device Model: WDC WD10EADX-00TDHB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 77.04D77 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Aug 26 16:52:19 2015 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (21180) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 244) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 2 3 Spin_Up_Time POS--K 197 181 021 - 6141 4 Start_Stop_Count -O--CK 098 098 000 - 2699 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 065 065 000 - 26084 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2582 192 Power-Off_Retract_Count -O--CK 200 200 000 - 695 193 Load_Cycle_Count -O--CK 048 048 000 - 458965 194 Temperature_Celsius -O---K 109 099 000 - 38 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 119 000 - 271579 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 98 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 98 [1] occurred at disk power-on lifetime: 13600 hours (566 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 e1 f9 28 e0 00 Error: UNC 8 sectors at LBA = 0x00e1f928 = 14809384 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 e1 f9 28 e0 00 23:08:47.328 READ DMA EXT 35 00 00 00 08 00 00 00 75 15 50 e0 00 23:08:47.328 WRITE DMA EXT 35 00 00 00 08 00 00 00 63 88 b0 e0 00 23:08:47.328 WRITE DMA EXT 35 00 00 00 08 00 00 00 63 27 f8 e0 00 23:08:47.328 WRITE DMA EXT 35 00 00 00 08 00 00 00 63 13 08 e0 00 23:08:47.328 WRITE DMA EXT Error 97 [0] occurred at disk power-on lifetime: 13600 hours (566 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 00 e1 f9 20 e0 00 Error: UNC 32 sectors at LBA = 0x00e1f920 = 14809376 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 00 e1 f9 20 e0 00 23:08:45.056 READ DMA EXT 35 00 00 00 20 00 00 06 c1 6b 80 e0 00 23:08:45.056 WRITE DMA EXT 35 00 00 00 80 00 00 06 ec 55 c0 e0 00 23:08:45.056 WRITE DMA EXT 25 00 00 00 80 00 00 00 c1 67 80 e0 00 23:08:45.039 READ DMA EXT 25 00 00 00 08 00 00 02 f1 48 c0 e0 00 23:08:45.027 READ DMA EXT Error 96 [23] occurred at disk power-on lifetime: 13448 hours (560 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 e1 f9 28 e0 00 Error: UNC 8 sectors at LBA = 0x00e1f928 = 14809384 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 e1 f9 28 e0 00 07:42:05.075 READ DMA EXT 25 00 00 00 08 00 00 00 e1 f9 20 e0 00 07:42:05.073 READ DMA EXT 25 00 00 00 20 00 00 00 7d 49 e0 e0 00 07:42:05.073 READ DMA EXT 25 00 00 00 40 00 00 00 7d 49 40 e0 00 07:42:05.051 READ DMA EXT 35 00 00 00 79 00 00 00 74 a5 68 e0 00 07:42:05.050 WRITE DMA EXT Error 95 [22] occurred at disk power-on lifetime: 13448 hours (560 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 00 e1 f9 20 e0 00 Error: UNC 64 sectors at LBA = 0x00e1f920 = 14809376 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 e1 f9 20 e0 00 07:42:02.762 READ DMA EXT 35 00 00 01 00 00 00 00 e0 de b8 e0 00 07:42:02.762 WRITE DMA EXT 35 00 00 01 00 00 00 00 e0 dd b8 e0 00 07:42:02.761 WRITE DMA EXT 35 00 00 01 00 00 00 00 e0 dc b8 e0 00 07:42:02.761 WRITE DMA EXT 35 00 00 01 00 00 00 00 e0 db b8 e0 00 07:42:02.760 WRITE DMA EXT Error 94 [21] occurred at disk power-on lifetime: 13423 hours (559 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 07 53 1e c8 e0 00 Error: UNC 8 sectors at LBA = 0x07531ec8 = 122887880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 07 53 1e c8 e0 00 02:31:19.444 READ DMA EXT 35 00 00 00 20 00 00 06 4a 8d a0 e0 00 02:31:19.444 WRITE DMA EXT 35 00 00 00 df 00 00 1b ea a0 a0 e0 00 02:31:19.443 WRITE DMA EXT 35 00 00 00 86 00 00 1b ea 9b e0 e0 00 02:31:19.443 WRITE DMA EXT 35 00 00 01 00 00 00 1b ea 9a e0 e0 00 02:31:19.442 WRITE DMA EXT Error 93 [20] occurred at disk power-on lifetime: 13423 hours (559 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 60 00 00 07 53 1e c0 e0 00 Error: UNC 96 sectors at LBA = 0x07531ec0 = 122887872 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 60 00 00 07 53 1e c0 e0 00 02:31:17.143 READ DMA EXT 35 00 00 00 60 00 00 07 4a 97 a0 e0 00 02:31:17.142 WRITE DMA EXT 25 00 00 00 40 00 00 06 6b 23 40 e0 00 02:31:17.115 READ DMA EXT 35 00 00 00 a0 00 00 01 90 0a e0 e0 00 02:31:17.114 WRITE DMA EXT 35 00 00 00 a0 00 00 01 8c 55 40 e0 00 02:31:17.114 WRITE DMA EXT Error 92 [19] occurred at disk power-on lifetime: 13410 hours (558 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 e1 f9 28 e0 00 Error: UNC 8 sectors at LBA = 0x00e1f928 = 14809384 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 e1 f9 28 e0 00 06:58:48.701 READ DMA EXT 35 00 00 00 10 00 00 00 63 14 68 e0 00 06:58:48.701 WRITE DMA EXT 35 00 00 00 08 00 00 00 60 1f 08 e0 00 06:58:48.701 WRITE DMA EXT 35 00 00 00 48 00 00 12 ea 10 78 e0 00 06:58:48.700 WRITE DMA EXT 35 00 00 00 20 00 00 06 e2 e0 40 e0 00 06:58:48.700 WRITE DMA EXT Error 91 [18] occurred at disk power-on lifetime: 13410 hours (558 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 00 e1 f9 20 e0 00 Error: UNC 256 sectors at LBA = 0x00e1f920 = 14809376 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 00 e1 f9 20 e0 00 06:58:46.316 READ DMA EXT 25 00 00 00 a0 00 00 00 e1 19 e0 e0 00 06:58:46.315 READ DMA EXT 25 00 00 01 00 00 00 00 e1 18 e0 e0 00 06:58:46.305 READ DMA EXT 25 00 00 00 40 00 00 00 df 65 e0 e0 00 06:58:46.305 READ DMA EXT 25 00 00 01 00 00 00 00 df 64 e0 e0 00 06:58:46.293 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 24545 - # 2 Short offline Completed without error 00% 18808 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 37/38 Celsius Lifetime Min/Max Temperature: 37/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (399) Index Estimated Time Temperature Celsius 400 2015-08-26 08:55 40 ********************* ... ..( 23 skipped). .. ********************* 424 2015-08-26 09:19 40 ********************* 425 2015-08-26 09:20 ? - 426 2015-08-26 09:21 23 **** 427 2015-08-26 09:22 24 ***** 428 2015-08-26 09:23 24 ***** 429 2015-08-26 09:24 25 ****** 430 2015-08-26 09:25 25 ****** 431 2015-08-26 09:26 26 ******* 432 2015-08-26 09:27 26 ******* 433 2015-08-26 09:28 26 ******* 434 2015-08-26 09:29 27 ******** 435 2015-08-26 09:30 27 ******** 436 2015-08-26 09:31 28 ********* 437 2015-08-26 09:32 28 ********* 438 2015-08-26 09:33 29 ********** ... ..( 2 skipped). .. ********** 441 2015-08-26 09:36 29 ********** 442 2015-08-26 09:37 30 *********** 443 2015-08-26 09:38 30 *********** 444 2015-08-26 09:39 31 ************ ... ..( 2 skipped). .. ************ 447 2015-08-26 09:42 31 ************ 448 2015-08-26 09:43 32 ************* 449 2015-08-26 09:44 32 ************* 450 2015-08-26 09:45 32 ************* 451 2015-08-26 09:46 ? - 452 2015-08-26 09:47 28 ********* 453 2015-08-26 09:48 28 ********* 454 2015-08-26 09:49 28 ********* 455 2015-08-26 09:50 29 ********** 456 2015-08-26 09:51 29 ********** 457 2015-08-26 09:52 29 ********** 458 2015-08-26 09:53 30 *********** 459 2015-08-26 09:54 30 *********** 460 2015-08-26 09:55 30 *********** 461 2015-08-26 09:56 31 ************ 462 2015-08-26 09:57 31 ************ 463 2015-08-26 09:58 32 ************* 464 2015-08-26 09:59 ? - 465 2015-08-26 10:00 26 ******* 466 2015-08-26 10:01 26 ******* 467 2015-08-26 10:02 26 ******* 468 2015-08-26 10:03 27 ******** 469 2015-08-26 10:04 28 ********* 470 2015-08-26 10:05 29 ********** ... ..( 3 skipped). .. ********** 474 2015-08-26 10:09 29 ********** 475 2015-08-26 10:10 30 *********** 476 2015-08-26 10:11 30 *********** 477 2015-08-26 10:12 31 ************ 0 2015-08-26 10:13 31 ************ 1 2015-08-26 10:14 31 ************ 2 2015-08-26 10:15 32 ************* ... ..( 2 skipped). .. ************* 5 2015-08-26 10:18 32 ************* 6 2015-08-26 10:19 33 ************** ... ..( 6 skipped). .. ************** 13 2015-08-26 10:26 33 ************** 14 2015-08-26 10:27 34 *************** ... ..( 5 skipped). .. *************** 20 2015-08-26 10:33 34 *************** 21 2015-08-26 10:34 35 **************** ... ..( 6 skipped). .. **************** 28 2015-08-26 10:41 35 **************** 29 2015-08-26 10:42 36 ***************** ... ..( 40 skipped). .. ***************** 70 2015-08-26 11:23 36 ***************** 71 2015-08-26 11:24 37 ****************** ... ..( 11 skipped). .. ****************** 83 2015-08-26 11:36 37 ****************** 84 2015-08-26 11:37 ? - 85 2015-08-26 11:38 37 ****************** ... ..( 3 skipped). .. ****************** 89 2015-08-26 11:42 37 ****************** 90 2015-08-26 11:43 38 ******************* 91 2015-08-26 11:44 37 ****************** ... ..( 16 skipped). .. ****************** 108 2015-08-26 12:01 37 ****************** 109 2015-08-26 12:02 38 ******************* 110 2015-08-26 12:03 37 ****************** 111 2015-08-26 12:04 37 ****************** 112 2015-08-26 12:05 37 ****************** 113 2015-08-26 12:06 38 ******************* 114 2015-08-26 12:07 38 ******************* 115 2015-08-26 12:08 38 ******************* 116 2015-08-26 12:09 39 ******************** ... ..( 23 skipped). .. ******************** 140 2015-08-26 12:33 39 ******************** 141 2015-08-26 12:34 40 ********************* 142 2015-08-26 12:35 39 ******************** ... ..( 25 skipped). .. ******************** 168 2015-08-26 13:01 39 ******************** 169 2015-08-26 13:02 40 ********************* ... ..( 2 skipped). .. ********************* 172 2015-08-26 13:05 40 ********************* 173 2015-08-26 13:06 39 ******************** 174 2015-08-26 13:07 39 ******************** 175 2015-08-26 13:08 39 ******************** 176 2015-08-26 13:09 40 ********************* ... ..( 7 skipped). .. ********************* 184 2015-08-26 13:17 40 ********************* 185 2015-08-26 13:18 39 ******************** ... ..( 8 skipped). .. ******************** 194 2015-08-26 13:27 39 ******************** 195 2015-08-26 13:28 40 ********************* 196 2015-08-26 13:29 40 ********************* 197 2015-08-26 13:30 39 ******************** ... ..( 4 skipped). .. ******************** 202 2015-08-26 13:35 39 ******************** 203 2015-08-26 13:36 40 ********************* 204 2015-08-26 13:37 39 ******************** ... ..( 4 skipped). .. ******************** 209 2015-08-26 13:42 39 ******************** 210 2015-08-26 13:43 40 ********************* 211 2015-08-26 13:44 39 ******************** ... ..( 45 skipped). .. ******************** 257 2015-08-26 14:30 39 ******************** 258 2015-08-26 14:31 40 ********************* 259 2015-08-26 14:32 39 ******************** 260 2015-08-26 14:33 40 ********************* ... ..( 3 skipped). .. ********************* 264 2015-08-26 14:37 40 ********************* 265 2015-08-26 14:38 39 ******************** ... ..( 5 skipped). .. ******************** 271 2015-08-26 14:44 39 ******************** 272 2015-08-26 14:45 40 ********************* ... ..(126 skipped). .. ********************* 399 2015-08-26 16:52 40 ********************* SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 1813 Vendor specific