/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.0-17-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Black Mobile Device Model: WDC WD3200BEKX-75B7WT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Feb 14 09:02:23 2024 WIB SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 68) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 2289 3 Spin_Up_Time POS--K 158 134 021 - 1058 4 Start_Stop_Count -O--CK 096 096 000 - 4944 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 081 081 000 - 14031 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3064 191 G-Sense_Error_Rate -O--CK 001 001 000 - 518 192 Power-Off_Retract_Count -O--CK 200 200 000 - 266 193 Load_Cycle_Count -O--CK 140 140 000 - 182081 194 Temperature_Celsius -O---K 096 086 000 - 47 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 5 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 240 Head_Flying_Hours -O--CK 083 083 000 - 12915 241 Total_LBAs_Written -O--CK 200 200 000 - 14632613203 242 Total_LBAs_Read -O--CK 200 200 000 - 32067929469 254 Free_Fall_Sensor -O--CK 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2280 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2280 [23] occurred at disk power-on lifetime: 12801 hours (533 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 24 d4 c0 0d 40 00 Error: UNC at LBA = 0x24d4c00d = 617922573 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 10 00 00 24 d4 bf f0 40 00 00:48:15.290 READ FPDMA QUEUED 60 00 08 00 08 00 00 03 cd 60 a8 40 00 00:48:15.290 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 00:48:15.290 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:48:15.290 SET FEATURES [Enable write cache] 60 01 00 00 28 00 00 24 d4 bf f0 40 00 00:48:13.299 READ FPDMA QUEUED Error 2279 [22] occurred at disk power-on lifetime: 12801 hours (533 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 24 d4 c0 0d 40 00 Error: UNC at LBA = 0x24d4c00d = 617922573 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 28 00 00 24 d4 bf f0 40 00 00:48:13.299 READ FPDMA QUEUED 61 00 02 00 10 00 00 00 2f 9f 48 40 00 00:48:13.299 WRITE FPDMA QUEUED 60 00 08 00 08 00 00 03 cd 60 a8 40 00 00:48:13.299 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 00:48:13.299 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:48:13.299 SET FEATURES [Enable write cache] Error 2278 [21] occurred at disk power-on lifetime: 12801 hours (533 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 24 d4 c0 0d 40 00 Error: WP at LBA = 0x24d4c00d = 617922573 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 28 00 00 22 03 f0 18 40 00 00:48:11.270 WRITE FPDMA QUEUED 61 00 08 00 10 00 00 00 14 92 38 40 00 00:48:11.270 WRITE FPDMA QUEUED 61 00 08 00 08 00 00 00 14 92 48 40 00 00:48:11.270 WRITE FPDMA QUEUED 60 00 08 00 20 00 00 03 cd 60 a8 40 00 00:48:11.269 READ FPDMA QUEUED 60 01 00 00 18 00 00 24 d4 bf f0 40 00 00:48:11.269 READ FPDMA QUEUED Error 2277 [20] occurred at disk power-on lifetime: 12801 hours (533 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 24 d4 c0 0d 40 00 Error: UNC at LBA = 0x24d4c00d = 617922573 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 20 00 00 03 cd 60 a8 40 00 00:48:09.286 READ FPDMA QUEUED 60 01 00 00 08 00 00 24 d4 bf f0 40 00 00:48:09.286 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 00:48:09.285 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:48:09.285 SET FEATURES [Enable write cache] 61 00 08 00 10 00 00 00 12 f9 08 40 00 00:48:07.241 WRITE FPDMA QUEUED Error 2276 [19] occurred at disk power-on lifetime: 12801 hours (533 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 24 d4 c0 0d 40 00 Error: WP at LBA = 0x24d4c00d = 617922573 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 10 00 00 00 12 f9 08 40 00 00:48:07.241 WRITE FPDMA QUEUED 61 00 08 00 08 00 00 00 14 92 40 40 00 00:48:07.240 WRITE FPDMA QUEUED 60 01 00 00 28 00 00 24 d4 bf f0 40 00 00:48:07.240 READ FPDMA QUEUED 61 00 02 00 18 00 00 00 2f 9f 48 40 00 00:48:07.240 WRITE FPDMA QUEUED 61 00 04 00 10 00 00 00 2a 76 18 40 00 00:48:07.240 WRITE FPDMA QUEUED Error 2275 [18] occurred at disk power-on lifetime: 12801 hours (533 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 24 d4 c0 0d 40 00 Error: WP at LBA = 0x24d4c00d = 617922573 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 10 00 00 18 bd 04 08 40 00 00:48:05.234 WRITE FPDMA QUEUED 61 00 08 00 10 00 00 18 bd 04 18 40 00 00:48:05.234 WRITE FPDMA QUEUED 60 01 00 00 08 00 00 24 d4 bf f0 40 00 00:48:05.233 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 00:48:05.233 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:48:05.233 SET FEATURES [Enable write cache] Error 2274 [17] occurred at disk power-on lifetime: 12801 hours (533 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 24 d4 c0 0d 40 00 Error: UNC at LBA = 0x24d4c00d = 617922573 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 18 00 00 24 d4 bf f0 40 00 00:48:03.228 READ FPDMA QUEUED 60 00 08 00 10 00 00 24 d4 c1 f0 40 00 00:48:03.227 READ FPDMA QUEUED 60 01 00 00 08 00 00 24 d4 c0 f0 40 00 00:48:03.227 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 00:48:03.227 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:48:03.227 SET FEATURES [Enable write cache] Error 2273 [16] occurred at disk power-on lifetime: 12801 hours (533 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 24 d4 c0 0d 40 00 Error: UNC at LBA = 0x24d4c00d = 617922573 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 c8 00 00 24 d4 bf f0 40 00 00:48:01.221 READ FPDMA QUEUED 60 00 08 00 10 00 00 24 d4 c1 f0 40 00 00:48:01.221 READ FPDMA QUEUED 60 01 00 00 08 00 00 24 d4 c0 f0 40 00 00:48:01.221 READ FPDMA QUEUED ef 00 90 00 03 00 00 00 00 00 00 00 00 00:48:01.221 SET FEATURES [Disable SATA feature] ef 00 02 00 00 00 00 00 00 00 00 00 00 00:48:01.221 SET FEATURES [Enable write cache] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 7995 - # 2 Short offline Completed without error 00% 7784 - # 3 Short offline Completed without error 00% 7777 - # 4 Short offline Completed without error 00% 7776 - # 5 Short offline Aborted by host 80% 7775 - # 6 Short offline Completed without error 00% 7775 - # 7 Short offline Completed without error 00% 7766 - # 8 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 47 Celsius Power Cycle Min/Max Temperature: --/47 Celsius Lifetime Min/Max Temperature: --/57 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (45) Index Estimated Time Temperature Celsius 46 2024-02-14 06:55 31 ************ 47 2024-02-14 06:56 31 ************ 48 2024-02-14 06:57 32 ************* 49 2024-02-14 06:58 33 ************** 50 2024-02-14 06:59 35 **************** 51 2024-02-14 07:00 35 **************** 52 2024-02-14 07:01 36 ***************** 53 2024-02-14 07:02 37 ****************** 54 2024-02-14 07:03 38 ******************* 55 2024-02-14 07:04 38 ******************* 56 2024-02-14 07:05 38 ******************* 57 2024-02-14 07:06 39 ******************** 58 2024-02-14 07:07 39 ******************** 59 2024-02-14 07:08 40 ********************* 60 2024-02-14 07:09 40 ********************* 61 2024-02-14 07:10 ? - 62 2024-02-14 07:11 0 - 63 2024-02-14 07:12 30 *********** 64 2024-02-14 07:13 31 ************ 65 2024-02-14 07:14 32 ************* 66 2024-02-14 07:15 33 ************** 67 2024-02-14 07:16 34 *************** 68 2024-02-14 07:17 35 **************** 69 2024-02-14 07:18 36 ***************** 70 2024-02-14 07:19 37 ****************** 71 2024-02-14 07:20 37 ****************** 72 2024-02-14 07:21 39 ******************** 73 2024-02-14 07:22 39 ******************** 74 2024-02-14 07:23 40 ********************* ... ..( 2 skipped). .. ********************* 77 2024-02-14 07:26 40 ********************* 78 2024-02-14 07:27 41 ********************** 79 2024-02-14 07:28 41 ********************** 80 2024-02-14 07:29 41 ********************** 81 2024-02-14 07:30 42 *********************** 82 2024-02-14 07:31 42 *********************** 83 2024-02-14 07:32 43 ************************ ... ..( 3 skipped). .. ************************ 87 2024-02-14 07:36 43 ************************ 88 2024-02-14 07:37 44 ************************* ... ..( 6 skipped). .. ************************* 95 2024-02-14 07:44 44 ************************* 96 2024-02-14 07:45 45 ************************** ... ..( 16 skipped). .. ************************** 113 2024-02-14 08:02 45 ************************** 114 2024-02-14 08:03 46 *************************** ... ..( 25 skipped). .. *************************** 12 2024-02-14 08:29 46 *************************** 13 2024-02-14 08:30 47 **************************** ... ..( 31 skipped). .. **************************** 45 2024-02-14 09:02 47 **************************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 45776 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 6700 Vendor specific