/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.8 Device Model: ST3300831AS Serial Number: -- Firmware Version: 3.03 User Capacity: 300 069 052 416 bytes [300 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Tue Aug 16 08:26:40 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 40) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 101) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 063 054 006 - 95369353 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 095 095 020 - 5738 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 084 060 030 - 257319314 9 Power_On_Hours -O--CK 067 067 000 - 29612 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4423 194 Temperature_Celsius -O---K 035 058 000 - 35 (0 11 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 063 054 000 - 95369353 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 1181 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1181 [0] occurred at disk power-on lifetime: 20911 hours (871 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 09 97 ae 32 ae e0 00 Error: UNC at LBA = 0x997ae32ae = 41199481518 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 01 00 09 97 00 32 ae e0 00 02:56:22.020 READ VERIFY SECTOR(S) EXT 42 00 00 00 02 00 09 97 00 32 ae e0 00 02:56:18.704 READ VERIFY SECTOR(S) EXT 42 00 00 00 02 00 09 97 00 32 ac e0 00 02:56:42.035 READ VERIFY SECTOR(S) EXT 42 00 00 00 04 00 09 97 00 32 ac e0 00 02:56:38.726 READ VERIFY SECTOR(S) EXT 42 00 00 00 04 00 09 97 00 32 a8 e0 00 02:56:38.705 READ VERIFY SECTOR(S) EXT Error 1180 [19] occurred at disk power-on lifetime: 20854 hours (868 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 b2 00 09 97 ae 32 ae e0 00 Error: UNC at LBA = 0x997ae32ae = 41199481518 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 01 00 00 09 97 00 32 60 e0 00 18:38:34.270 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 09 96 00 32 60 e0 00 18:38:34.268 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 09 95 00 32 60 e0 00 18:38:34.265 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 09 94 00 32 60 e0 00 18:38:34.263 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 09 93 00 32 60 e0 00 18:38:34.260 READ VERIFY SECTOR(S) EXT Error 1179 [18] occurred at disk power-on lifetime: 20813 hours (867 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 86 00 09 97 ae 32 ae e0 00 Error: UNC 134 sectors at LBA = 0x997ae32ae = 41199481518 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 09 97 00 32 28 e0 00 04:28:37.355 READ DMA EXT 25 00 00 01 00 00 09 96 00 32 28 e0 00 04:28:37.353 READ DMA EXT 25 00 00 01 00 00 09 95 00 32 28 e0 00 04:28:37.350 READ DMA EXT 25 00 00 01 00 00 09 94 00 32 28 e0 00 04:28:37.348 READ DMA EXT 25 00 00 01 00 00 09 93 00 32 28 e0 00 04:28:37.346 READ DMA EXT Error 1178 [17] occurred at disk power-on lifetime: 20809 hours (867 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 09 66 00 66 e0 00 Error: UNC 6 sectors at LBA = 0x09660066 = 157679718 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 09 00 00 60 e0 00 00:18:31.698 READ DMA EXT 25 00 00 00 08 00 00 09 00 00 60 e0 00 00:18:31.696 READ DMA EXT 25 00 00 00 08 00 00 02 00 e7 18 e0 00 00:18:31.694 READ DMA EXT 25 00 00 00 08 00 00 8c 00 15 88 e0 00 00:18:31.691 READ DMA EXT 25 00 00 00 08 00 00 1e 00 60 90 e0 00 00:18:31.686 READ DMA EXT Error 1177 [16] occurred at disk power-on lifetime: 20911 hours (871 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 09 97 ae 32 ae e0 00 Error: UNC at LBA = 0x997ae32ae = 41199481518 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 01 00 09 97 00 32 ae e0 00 02:56:22.020 READ VERIFY SECTOR(S) EXT 42 00 00 00 02 00 09 97 00 32 ae e0 00 02:56:18.704 READ VERIFY SECTOR(S) EXT 42 00 00 00 02 00 09 97 00 32 ac e0 00 02:56:42.035 READ VERIFY SECTOR(S) EXT 42 00 00 00 04 00 09 97 00 32 ac e0 00 02:56:38.726 READ VERIFY SECTOR(S) EXT 42 00 00 00 04 00 09 97 00 32 a8 e0 00 02:56:38.705 READ VERIFY SECTOR(S) EXT Error 1176 [15] occurred at disk power-on lifetime: 20854 hours (868 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 b2 00 09 97 ae 32 ae e0 00 Error: UNC at LBA = 0x997ae32ae = 41199481518 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 01 00 00 09 97 00 32 60 e0 00 18:38:34.270 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 09 96 00 32 60 e0 00 18:38:34.268 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 09 95 00 32 60 e0 00 18:38:34.265 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 09 94 00 32 60 e0 00 18:38:34.263 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 09 93 00 32 60 e0 00 18:38:34.260 READ VERIFY SECTOR(S) EXT Error 1175 [14] occurred at disk power-on lifetime: 20813 hours (867 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 86 00 09 97 ae 32 ae e0 00 Error: UNC 134 sectors at LBA = 0x997ae32ae = 41199481518 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 09 97 00 32 28 e0 00 04:28:37.355 READ DMA EXT 25 00 00 01 00 00 09 96 00 32 28 e0 00 04:28:37.353 READ DMA EXT 25 00 00 01 00 00 09 95 00 32 28 e0 00 04:28:37.350 READ DMA EXT 25 00 00 01 00 00 09 94 00 32 28 e0 00 04:28:37.348 READ DMA EXT 25 00 00 01 00 00 09 93 00 32 28 e0 00 04:28:37.346 READ DMA EXT Error 1174 [13] occurred at disk power-on lifetime: 20809 hours (867 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 09 66 00 66 e0 00 Error: UNC 6 sectors at LBA = 0x09660066 = 157679718 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 09 00 00 60 e0 00 00:18:31.698 READ DMA EXT 25 00 00 00 08 00 00 09 00 00 60 e0 00 00:18:31.696 READ DMA EXT 25 00 00 00 08 00 00 02 00 e7 18 e0 00 00:18:31.694 READ DMA EXT 25 00 00 00 08 00 00 8c 00 15 88 e0 00 00:18:31.691 READ DMA EXT 25 00 00 00 08 00 00 1e 00 60 90 e0 00 00:18:31.686 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 80% 2157 - # 2 Extended offline Completed without error 00% 738 - # 3 Extended offline Completed without error 00% 61 - # 4 Short offline Completed without error 00% 59 - # 5 Short offline Completed without error 00% 57 - # 6 Extended offline Interrupted (host reset) 90% 57 - # 7 Short offline Completed without error 00% 57 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported ATA_READ_LOG_EXT (addr=0x11:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read SATA Phy Event Counters failed /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3160215AS Serial Number: -- Firmware Version: 4.AAB User Capacity: 160 041 885 696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Tue Aug 16 08:26:41 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 54) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 253 006 - 0 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 079 079 020 - 21666 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 089 060 030 - 896684686 9 Power_On_Hours -O--CK 074 074 000 - 23476 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 078 078 020 - 23079 187 Reported_Uncorrect -O--CK 001 001 000 - 1175 189 High_Fly_Writes -O-RCK 060 060 000 - 40 190 Airflow_Temperature_Cel -O---K 065 035 045 Past 35 (1 96 37 31 0) 194 Temperature_Celsius -O---K 035 065 000 - 35 (0 16 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 072 066 000 - 17880677 197 Current_Pending_Sector -O--C- 100 100 000 - 1 198 Offline_Uncorrectable ----C- 100 100 000 - 1 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 1177 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1177 [16] occurred at disk power-on lifetime: 16001 hours (666 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 ed 00 bc a1 e0 00 Error: UNC at LBA = 0x1ed00bca1 = 8271215777 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 ed 00 bc a0 e0 00 00:53:41.923 READ DMA EXT 35 00 00 00 08 00 01 df 00 a4 c0 e0 00 00:53:41.923 WRITE DMA EXT 35 00 00 00 08 00 01 42 00 a2 d8 e0 00 00:53:41.923 WRITE DMA EXT 25 00 00 00 40 00 01 1d 00 a2 d2 e0 00 00:53:41.922 READ DMA EXT 35 00 00 00 08 00 01 38 00 a1 e8 e0 00 00:53:41.921 WRITE DMA EXT Error 1176 [15] occurred at disk power-on lifetime: 16001 hours (666 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 ed 00 bc a1 e0 00 Error: UNC at LBA = 0x1ed00bca1 = 8271215777 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 ed 00 bc a0 e0 00 00:53:54.560 READ DMA EXT 25 00 00 00 40 00 01 ed 00 a1 52 e0 00 00:53:54.554 READ DMA EXT 25 00 00 00 08 00 01 86 00 80 20 e0 00 00:53:54.548 READ DMA EXT 25 00 00 00 18 00 01 1f 00 6d 48 e0 00 00:53:54.544 READ DMA EXT 35 00 00 00 80 00 01 aa 00 26 88 e0 00 00:53:54.536 WRITE DMA EXT Error 1175 [14] occurred at disk power-on lifetime: 16001 hours (666 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 ed 00 bc a1 e0 00 Error: UNC at LBA = 0x1ed00bca1 = 8271215777 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 ed 00 bc a0 e0 00 00:53:51.058 READ DMA EXT 25 00 00 00 08 00 01 a7 00 b2 d8 e0 00 00:53:51.054 READ DMA EXT 35 00 00 00 08 00 01 f3 00 a6 08 e0 00 00:53:51.035 WRITE DMA EXT 25 00 00 00 40 00 01 ed 00 a1 12 e0 00 00:53:51.034 READ DMA EXT 25 00 00 00 40 00 01 eb 00 82 2a e0 00 00:53:51.033 READ DMA EXT Error 1174 [13] occurred at disk power-on lifetime: 16001 hours (666 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 ed 00 bc a1 e0 00 Error: UNC at LBA = 0x1ed00bca1 = 8271215777 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 ed 00 bc a0 e0 00 00:53:47.382 READ DMA EXT 25 00 00 00 08 00 01 a1 00 b2 58 e0 00 00:53:47.376 READ DMA EXT 25 00 00 00 40 00 01 ec 00 a1 d2 e0 00 00:53:47.369 READ DMA EXT 25 00 00 00 08 00 01 84 00 80 80 e0 00 00:53:47.472 READ DMA EXT 25 00 00 00 40 00 00 89 00 4e 68 e0 00 00:53:47.469 READ DMA EXT Error 1173 [12] occurred at disk power-on lifetime: 16001 hours (666 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 ed 00 bc a1 e0 00 Error: UNC at LBA = 0x1ed00bca1 = 8271215777 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 ed 00 bc a0 e0 00 00:53:41.923 READ DMA EXT 35 00 00 00 08 00 01 df 00 a4 c0 e0 00 00:53:41.923 WRITE DMA EXT 35 00 00 00 08 00 01 42 00 a2 d8 e0 00 00:53:41.923 WRITE DMA EXT 25 00 00 00 40 00 01 1d 00 a2 d2 e0 00 00:53:41.922 READ DMA EXT 35 00 00 00 08 00 01 38 00 a1 e8 e0 00 00:53:41.921 WRITE DMA EXT Error 1172 [11] occurred at disk power-on lifetime: 16001 hours (666 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 ed 00 bc a1 e0 00 Error: UNC at LBA = 0x1ed00bca1 = 8271215777 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 ed 00 bc a0 e0 00 00:53:54.560 READ DMA EXT 25 00 00 00 40 00 01 ed 00 a1 52 e0 00 00:53:54.554 READ DMA EXT 25 00 00 00 08 00 01 86 00 80 20 e0 00 00:53:54.548 READ DMA EXT 25 00 00 00 18 00 01 1f 00 6d 48 e0 00 00:53:54.544 READ DMA EXT 35 00 00 00 80 00 01 aa 00 26 88 e0 00 00:53:54.536 WRITE DMA EXT Error 1171 [10] occurred at disk power-on lifetime: 16001 hours (666 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 ed 00 bc a1 e0 00 Error: UNC at LBA = 0x1ed00bca1 = 8271215777 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 ed 00 bc a0 e0 00 00:53:51.058 READ DMA EXT 25 00 00 00 08 00 01 a7 00 b2 d8 e0 00 00:53:51.054 READ DMA EXT 35 00 00 00 08 00 01 f3 00 a6 08 e0 00 00:53:51.035 WRITE DMA EXT 25 00 00 00 40 00 01 ed 00 a1 12 e0 00 00:53:51.034 READ DMA EXT 25 00 00 00 40 00 01 eb 00 82 2a e0 00 00:53:51.033 READ DMA EXT Error 1170 [9] occurred at disk power-on lifetime: 16001 hours (666 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 ed 00 bc a1 e0 00 Error: UNC at LBA = 0x1ed00bca1 = 8271215777 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 01 ed 00 bc a0 e0 00 00:53:47.382 READ DMA EXT 25 00 00 00 08 00 01 a1 00 b2 58 e0 00 00:53:47.376 READ DMA EXT 25 00 00 00 40 00 01 ec 00 a1 d2 e0 00 00:53:47.369 READ DMA EXT 25 00 00 00 08 00 01 84 00 80 80 e0 00 00:53:47.472 READ DMA EXT 25 00 00 00 40 00 00 89 00 4e 68 e0 00 00:53:47.469 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 169 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS