/dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Caviar SE Serial ATA Device Model: WDC WD2500JS-00NCB1 Serial Number: -- Firmware Version: 10.02E02 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Thu Apr 4 01:24:11 2019 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7680) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 90) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 2617 3 Spin_Up_Time PO---- 195 172 021 - 5233 4 Start_Stop_Count -O--CK 094 094 000 - 6346 5 Reallocated_Sector_Ct PO--CK 189 189 140 - 81 7 Seek_Error_Rate POSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 034 034 000 - 48277 10 Spin_Retry_Count PO--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4839 190 Airflow_Temperature_Cel -O---K 056 037 045 Past 44 194 Temperature_Celsius -O---K 106 087 000 - 44 196 Reallocated_Event_Count -O--CK 173 173 000 - 27 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 7131 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 14 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 14 [13] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c5 25 95 5c 00 00 00 00 00 03 00 05 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 00 00 08 95 c4 00 5c 25 00 03 00 00:00:51.208 NOP [Abort queued commands] 00 8c 25 95 5c 00 68 00 e8 00 03 00 00 16:42:00.209 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 00 00 48 95 82 00 5c 25 00 03 00 00:00:57.352 NOP [Abort queued commands] Error 13 [12] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 f0 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 98 25 90 44 00 00 00 00 00 03 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 28 00 00 20 90 98 00 44 35 00 03 00 00:00:15.344 NOP [Abort queued commands] 00 98 35 90 44 00 08 00 98 00 03 00 00 16:36:26.392 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 00 00 00 90 38 00 42 c6 00 03 00 00:00:36.888 NOP [Abort queued commands] Error 12 [11] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 90 25 62 4d 00 00 00 00 00 03 00 05 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 08 62 90 05 4d 25 00 03 00 00:00:40.960 NOP [Abort queued commands] 05 82 25 62 4d 00 90 00 78 00 03 00 05 15:46:14.028 [RESERVED] 00 08 00 00 98 62 7e 05 4d 25 00 03 00 00:00:39.136 NOP [Abort queued commands] Error 11 [10] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 2f 25 61 54 00 00 00 00 00 03 00 05 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 00 00 18 61 2e 05 54 25 00 03 00 00:00:06.144 NOP [Abort queued commands] 05 20 25 61 54 00 d8 00 20 00 03 00 05 15:45:10.182 [RESERVED] 00 08 00 00 30 61 20 05 54 25 00 03 00 00:00:30.880 NOP [Abort queued commands] Error 10 [9] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 20 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 ca 25 de cd 00 00 00 00 00 02 00 05 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 00 00 c8 de ca 05 cd 25 00 02 00 00:01:03.520 NOP [Abort queued commands] 05 c5 25 de cd 00 10 00 b8 00 02 00 05 13:22:36.104 [RESERVED] 00 70 00 00 e8 de c4 05 cd 25 00 02 00 00:00:55.488 NOP [Abort queued commands] Error 9 [8] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 7c 25 dc c1 00 00 00 00 00 02 00 05 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 98 dc e2 05 c0 25 00 02 00 00:00:40.960 NOP [Abort queued commands] 05 dc 25 dc c0 00 e0 00 d8 00 02 00 05 13:20:21.727 [RESERVED] 00 98 00 00 e0 dc db 05 c0 25 00 02 00 00:00:30.960 NOP [Abort queued commands] Error 8 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 e4 25 15 5a 00 00 00 00 00 02 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 c8 14 04 00 da 25 00 02 00 00:00:51.200 NOP [Abort queued commands] 00 02 25 14 da 00 68 00 60 00 02 00 00 09:42:00.963 NOP [Reserved subcommand] [OBS-ACS-2] 00 a0 00 00 88 14 01 00 da 25 00 02 00 00:00:10.264 NOP [Abort queued commands] Error 7 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 e0 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 46 25 0c 2a 00 00 00 00 00 02 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 90 0c 71 00 1e 35 00 02 00 00:00:16.608 NOP [Abort queued commands] 00 71 35 0c 1e 00 08 00 a8 00 02 00 00 09:32:28.657 NOP [Reserved subcommand] [OBS-ACS-2] 00 75 00 00 e8 0c d7 01 0e 35 00 02 00 00:00:04.144 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 33097 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 44 Celsius Power Cycle Max Temperature: 44 Celsius Lifetime Max Temperature: 63 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/65 Celsius Min/Max Temperature Limit: 1/70 Celsius Temperature History Size (Index): 128 (90) Index Estimated Time Temperature Celsius 91 2019-04-03 23:17 44 ************************* ... ..( 4 skipped). .. ************************* 96 2019-04-03 23:22 44 ************************* 97 2019-04-03 23:23 41 ********************** 98 2019-04-03 23:24 39 ******************** 99 2019-04-03 23:25 38 ******************* 100 2019-04-03 23:26 41 ********************** 101 2019-04-03 23:27 42 *********************** 102 2019-04-03 23:28 41 ********************** 103 2019-04-03 23:29 38 ******************* 104 2019-04-03 23:30 38 ******************* 105 2019-04-03 23:31 41 ********************** 106 2019-04-03 23:32 44 ************************* 107 2019-04-03 23:33 42 *********************** 108 2019-04-03 23:34 42 *********************** 109 2019-04-03 23:35 40 ********************* 110 2019-04-03 23:36 42 *********************** 111 2019-04-03 23:37 42 *********************** 112 2019-04-03 23:38 42 *********************** 113 2019-04-03 23:39 39 ******************** 114 2019-04-03 23:40 36 ***************** 115 2019-04-03 23:41 37 ****************** 116 2019-04-03 23:42 40 ********************* 117 2019-04-03 23:43 43 ************************ 118 2019-04-03 23:44 41 ********************** 119 2019-04-03 23:45 39 ******************** 120 2019-04-03 23:46 39 ******************** 121 2019-04-03 23:47 42 *********************** 122 2019-04-03 23:48 43 ************************ 123 2019-04-03 23:49 43 ************************ 124 2019-04-03 23:50 44 ************************* 125 2019-04-03 23:51 44 ************************* 126 2019-04-03 23:52 41 ********************** 127 2019-04-03 23:53 41 ********************** 0 2019-04-03 23:54 41 ********************** 1 2019-04-03 23:55 44 ************************* 2 2019-04-03 23:56 41 ********************** 3 2019-04-03 23:57 39 ******************** 4 2019-04-03 23:58 38 ******************* 5 2019-04-03 23:59 40 ********************* 6 2019-04-04 00:00 44 ************************* 7 2019-04-04 00:01 42 *********************** 8 2019-04-04 00:02 43 ************************ 9 2019-04-04 00:03 42 *********************** 10 2019-04-04 00:04 44 ************************* 11 2019-04-04 00:05 42 *********************** 12 2019-04-04 00:06 39 ******************** 13 2019-04-04 00:07 39 ******************** 14 2019-04-04 00:08 41 ********************** 15 2019-04-04 00:09 44 ************************* 16 2019-04-04 00:10 46 *************************** 17 2019-04-04 00:11 45 ************************** 18 2019-04-04 00:12 44 ************************* 19 2019-04-04 00:13 42 *********************** 20 2019-04-04 00:14 42 *********************** 21 2019-04-04 00:15 44 ************************* 22 2019-04-04 00:16 44 ************************* 23 2019-04-04 00:17 41 ********************** 24 2019-04-04 00:18 ? - 25 2019-04-04 00:19 39 ******************** 26 2019-04-04 00:20 37 ****************** 27 2019-04-04 00:21 37 ****************** 28 2019-04-04 00:22 37 ****************** 29 2019-04-04 00:23 38 ******************* ... ..( 3 skipped). .. ******************* 33 2019-04-04 00:27 38 ******************* 34 2019-04-04 00:28 40 ********************* 35 2019-04-04 00:29 40 ********************* 36 2019-04-04 00:30 42 *********************** 37 2019-04-04 00:31 42 *********************** 38 2019-04-04 00:32 43 ************************ 39 2019-04-04 00:33 43 ************************ 40 2019-04-04 00:34 43 ************************ 41 2019-04-04 00:35 44 ************************* 42 2019-04-04 00:36 44 ************************* 43 2019-04-04 00:37 44 ************************* 44 2019-04-04 00:38 43 ************************ 45 2019-04-04 00:39 43 ************************ 46 2019-04-04 00:40 43 ************************ 47 2019-04-04 00:41 44 ************************* ... ..( 42 skipped). .. ************************* 90 2019-04-04 01:24 44 ************************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x8000 4 4126 Vendor specific