/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-00RKKA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 1,000,203,804,160 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jan 13 15:54:50 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10140) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 117) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x30b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 174 172 021 - 2258 4 Start_Stop_Count -O--CK 097 097 000 - 3041 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 087 087 000 - 10110 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2988 192 Power-Off_Retract_Count -O--CK 199 199 000 - 851 193 Load_Cycle_Count -O--CK 200 200 000 - 2189 194 Temperature_Celsius -O---K 113 096 000 - 30 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 41055 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 41055 [14] occurred at disk power-on lifetime: 5087 hours (211 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 08 00 00 00 2a 8c cf e0 00 Device Fault; Error: ABRT 8 sectors at LBA = 0x002a8ccf = 2788559 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 00 2a 8c cf e0 08 15:29:06.051 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.050 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.050 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:29:06.049 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.049 SET FEATURES [Enable SATA feature] Error 41054 [13] occurred at disk power-on lifetime: 5087 hours (211 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.050 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.050 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:29:06.049 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.049 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.048 IDENTIFY DEVICE Error 41053 [12] occurred at disk power-on lifetime: 5087 hours (211 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:29:06.049 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.049 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.048 IDENTIFY DEVICE c8 00 00 00 08 00 00 00 2a 8c cf e0 08 15:29:06.038 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.038 SET FEATURES [Enable SATA feature] Error 41052 [11] occurred at disk power-on lifetime: 5087 hours (211 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.049 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.048 IDENTIFY DEVICE c8 00 00 00 08 00 00 00 2a 8c cf e0 08 15:29:06.038 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.038 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.037 IDENTIFY DEVICE Error 41051 [10] occurred at disk power-on lifetime: 5087 hours (211 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 08 00 00 00 2a 8c cf e0 00 Device Fault; Error: ABRT 8 sectors at LBA = 0x002a8ccf = 2788559 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 00 2a 8c cf e0 08 15:29:06.038 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.038 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.037 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:29:06.037 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.037 SET FEATURES [Enable SATA feature] Error 41050 [9] occurred at disk power-on lifetime: 5087 hours (211 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.038 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.037 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:29:06.037 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.037 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.035 IDENTIFY DEVICE Error 41049 [8] occurred at disk power-on lifetime: 5087 hours (211 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 a0 08 15:29:06.037 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.037 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.035 IDENTIFY DEVICE c8 00 00 00 08 00 00 00 2a 8c cf e0 08 15:29:06.026 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.025 SET FEATURES [Enable SATA feature] Error 41048 [7] occurred at disk power-on lifetime: 5087 hours (211 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.037 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.035 IDENTIFY DEVICE c8 00 00 00 08 00 00 00 2a 8c cf e0 08 15:29:06.026 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 15:29:06.025 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 15:29:06.024 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 10088 - # 2 Extended offline Completed without error 00% 9928 - # 3 Extended offline Completed without error 00% 9741 - # 4 Extended offline Completed without error 00% 9571 - # 5 Extended offline Completed without error 00% 9527 - # 6 Extended offline Completed without error 00% 9483 - # 7 Extended offline Completed without error 00% 9448 - # 8 Extended offline Completed without error 00% 9387 - # 9 Extended offline Completed without error 00% 9293 - #10 Extended offline Completed without error 00% 9229 - #11 Extended offline Interrupted (host reset) 70% 8207 - #12 Extended offline Completed without error 00% 7765 - #13 Extended offline Completed without error 00% 7546 - #14 Extended offline Completed without error 00% 7017 - #15 Extended offline Completed without error 00% 6723 - #16 Extended offline Completed without error 00% 6664 - #17 Extended offline Completed without error 00% 6582 - #18 Extended offline Completed without error 00% 6321 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 27/30 Celsius Lifetime Min/Max Temperature: 27/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (171) Index Estimated Time Temperature Celsius 172 2017-01-13 07:57 36 ***************** ... ..( 24 skipped). .. ***************** 197 2017-01-13 08:22 36 ***************** 198 2017-01-13 08:23 ? - 199 2017-01-13 08:24 21 ** 200 2017-01-13 08:25 22 *** 201 2017-01-13 08:26 23 **** 202 2017-01-13 08:27 23 **** 203 2017-01-13 08:28 24 ***** 204 2017-01-13 08:29 25 ****** 205 2017-01-13 08:30 26 ******* 206 2017-01-13 08:31 26 ******* 207 2017-01-13 08:32 27 ******** 208 2017-01-13 08:33 27 ******** 209 2017-01-13 08:34 27 ******** 210 2017-01-13 08:35 28 ********* 211 2017-01-13 08:36 28 ********* 212 2017-01-13 08:37 29 ********** 213 2017-01-13 08:38 29 ********** 214 2017-01-13 08:39 30 *********** ... ..( 3 skipped). .. *********** 218 2017-01-13 08:43 30 *********** 219 2017-01-13 08:44 31 ************ 220 2017-01-13 08:45 31 ************ 221 2017-01-13 08:46 31 ************ 222 2017-01-13 08:47 32 ************* 223 2017-01-13 08:48 32 ************* 224 2017-01-13 08:49 32 ************* 225 2017-01-13 08:50 ? - 226 2017-01-13 08:51 21 ** 227 2017-01-13 08:52 22 *** 228 2017-01-13 08:53 23 **** 229 2017-01-13 08:54 23 **** 230 2017-01-13 08:55 24 ***** 231 2017-01-13 08:56 25 ****** 232 2017-01-13 08:57 26 ******* 233 2017-01-13 08:58 26 ******* 234 2017-01-13 08:59 27 ******** 235 2017-01-13 09:00 27 ******** 236 2017-01-13 09:01 28 ********* 237 2017-01-13 09:02 28 ********* 238 2017-01-13 09:03 29 ********** 239 2017-01-13 09:04 30 *********** ... ..( 2 skipped). .. *********** 242 2017-01-13 09:07 30 *********** 243 2017-01-13 09:08 31 ************ 244 2017-01-13 09:09 31 ************ 245 2017-01-13 09:10 31 ************ 246 2017-01-13 09:11 32 ************* 247 2017-01-13 09:12 32 ************* 248 2017-01-13 09:13 32 ************* 249 2017-01-13 09:14 33 ************** ... ..( 2 skipped). .. ************** 252 2017-01-13 09:17 33 ************** 253 2017-01-13 09:18 34 *************** ... ..( 5 skipped). .. *************** 259 2017-01-13 09:24 34 *************** 260 2017-01-13 09:25 35 **************** ... ..( 24 skipped). .. **************** 285 2017-01-13 09:50 35 **************** 286 2017-01-13 09:51 36 ***************** ... ..( 27 skipped). .. ***************** 314 2017-01-13 10:19 36 ***************** 315 2017-01-13 10:20 37 ****************** ... ..(112 skipped). .. ****************** 428 2017-01-13 12:13 37 ****************** 429 2017-01-13 12:14 38 ******************* ... ..( 56 skipped). .. ******************* 8 2017-01-13 13:11 38 ******************* 9 2017-01-13 13:12 37 ****************** ... ..( 10 skipped). .. ****************** 20 2017-01-13 13:23 37 ****************** 21 2017-01-13 13:24 38 ******************* ... ..( 11 skipped). .. ******************* 33 2017-01-13 13:36 38 ******************* 34 2017-01-13 13:37 ? - 35 2017-01-13 13:38 39 ******************** 36 2017-01-13 13:39 ? - 37 2017-01-13 13:40 39 ******************** 38 2017-01-13 13:41 39 ******************** 39 2017-01-13 13:42 ? - 40 2017-01-13 13:43 39 ******************** ... ..( 3 skipped). .. ******************** 44 2017-01-13 13:47 39 ******************** 45 2017-01-13 13:48 38 ******************* ... ..( 26 skipped). .. ******************* 72 2017-01-13 14:15 38 ******************* 73 2017-01-13 14:16 ? - 74 2017-01-13 14:17 39 ******************** 75 2017-01-13 14:18 38 ******************* 76 2017-01-13 14:19 38 ******************* 77 2017-01-13 14:20 ? - 78 2017-01-13 14:21 39 ******************** 79 2017-01-13 14:22 39 ******************** 80 2017-01-13 14:23 39 ******************** 81 2017-01-13 14:24 ? - 82 2017-01-13 14:25 39 ******************** 83 2017-01-13 14:26 39 ******************** 84 2017-01-13 14:27 ? - 85 2017-01-13 14:28 39 ******************** 86 2017-01-13 14:29 38 ******************* ... ..( 23 skipped). .. ******************* 110 2017-01-13 14:53 38 ******************* 111 2017-01-13 14:54 37 ****************** ... ..( 13 skipped). .. ****************** 125 2017-01-13 15:08 37 ****************** 126 2017-01-13 15:09 ? - 127 2017-01-13 15:10 37 ****************** 128 2017-01-13 15:11 ? - 129 2017-01-13 15:12 22 *** 130 2017-01-13 15:13 ? - 131 2017-01-13 15:14 23 **** 132 2017-01-13 15:15 ? - 133 2017-01-13 15:16 26 ******* 134 2017-01-13 15:17 ? - 135 2017-01-13 15:18 27 ******** 136 2017-01-13 15:19 27 ******** 137 2017-01-13 15:20 ? - 138 2017-01-13 15:21 27 ******** 139 2017-01-13 15:22 27 ******** 140 2017-01-13 15:23 27 ******** 141 2017-01-13 15:24 28 ********* 142 2017-01-13 15:25 29 ********** 143 2017-01-13 15:26 30 *********** 144 2017-01-13 15:27 36 ***************** ... ..( 26 skipped). .. ***************** 171 2017-01-13 15:54 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 379 Vendor specific /dev/sdb === START OF INFORMATION SECTION === Device Model: SPCC Solid State Disk Serial Number: -- Firmware Version: SAFM22.3 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jan 13 15:54:51 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 30) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 422 12 Power_Cycle_Count -O--C- 100 100 000 - 164 168 Unknown_Attribute -O--C- 100 100 000 - 2 170 Unknown_Attribute PO---- 100 100 010 - 752 173 Unknown_Attribute -O--C- 100 100 000 - 1 192 Power-Off_Retract_Count -O--C- 100 100 000 - 14 194 Temperature_Celsius PO---K 098 098 057 - 30 (Min/Max 30/30) 218 Unknown_Attribute PO-R-- 100 100 050 - 2 231 Temperature_Celsius PO--C- 100 100 000 - 100 241 Total_LBAs_Written -O--C- 100 100 000 - 235 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 6 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 397 - # 2 Extended offline Completed without error 00% 372 - # 3 Extended offline Completed without error 00% 288 - # 4 Extended offline Completed without error 00% 237 - # 5 Extended offline Completed without error 00% 75 - # 6 Extended offline Completed without error 00% 49 - # 7 Extended offline Completed without error 00% 13 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 164 --- Lifetime Power-On Resets 0x01 0x010 4 422 --- Power-on Hours 0x01 0x018 6 493198598 --- Logical Sectors Written 0x01 0x020 6 7552988 --- Number of Write Commands 0x01 0x028 6 127820550 --- Logical Sectors Read 0x01 0x030 6 1786526 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 32 --- Current Temperature 0x05 0x010 1 32 --- Average Short Term Temperature 0x05 0x018 1 32 --- Average Long Term Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 5 --- Lowest Temperature 0x05 0x030 1 50 --- Highest Average Short Term Temperature 0x05 0x038 1 16 --- Lowest Average Short Term Temperature 0x05 0x040 1 50 --- Highest Average Long Term Temperature 0x05 0x048 1 16 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 50 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 28238 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 9 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc === START OF INFORMATION SECTION === Model Family: Western Digital Green Device Model: WDC WD10EZRX-00L4HB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jan 13 15:54:51 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12360) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 142) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 144 122 021 - 3783 4 Start_Stop_Count -O--CK 098 098 000 - 2179 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 090 090 000 - 7633 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2132 192 Power-Off_Retract_Count -O--CK 200 200 000 - 430 193 Load_Cycle_Count -O--CK 192 192 000 - 24928 194 Temperature_Celsius -O---K 116 097 000 - 27 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 410 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 410 [1] occurred at disk power-on lifetime: 6160 hours (256 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 ff 98 80 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 08 17:12:37.648 FLUSH CACHE EXT b0 00 da 00 00 00 00 00 c2 4f 00 00 08 17:10:24.282 SMART RETURN STATUS b0 00 d0 00 01 00 00 00 c2 4f 00 00 08 17:10:24.280 SMART READ DATA b0 00 d1 00 01 00 00 00 c2 4f 00 00 08 17:10:24.278 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] e5 00 00 00 00 00 00 00 00 00 00 00 08 17:10:24.277 CHECK POWER MODE Error 409 [0] occurred at disk power-on lifetime: 6127 hours (255 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.123 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:06:18.123 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:06:18.123 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.123 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:06:18.122 IDENTIFY DEVICE Error 408 [23] occurred at disk power-on lifetime: 6127 hours (255 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:06:18.123 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.123 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:06:18.122 IDENTIFY DEVICE ca 00 00 00 08 00 00 00 00 21 47 e0 08 00:06:18.113 WRITE DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.113 SET FEATURES [Enable SATA feature] Error 407 [22] occurred at disk power-on lifetime: 6127 hours (255 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.123 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:06:18.122 IDENTIFY DEVICE ca 00 00 00 08 00 00 00 00 21 47 e0 08 00:06:18.113 WRITE DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.113 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:06:18.112 IDENTIFY DEVICE Error 406 [21] occurred at disk power-on lifetime: 6127 hours (255 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 08 00 00 00 00 21 47 e0 00 Device Fault; Error: ABRT at LBA = 0x00002147 = 8519 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ca 00 00 00 08 00 00 00 00 21 47 e0 08 00:06:18.113 WRITE DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.113 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:06:18.112 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:06:18.112 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.112 SET FEATURES [Enable SATA feature] Error 405 [20] occurred at disk power-on lifetime: 6127 hours (255 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.113 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:06:18.112 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:06:18.112 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.112 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:06:18.111 IDENTIFY DEVICE Error 404 [19] occurred at disk power-on lifetime: 6127 hours (255 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:06:18.112 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.112 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:06:18.111 IDENTIFY DEVICE ca 00 00 00 08 00 00 00 00 21 47 e0 08 00:06:18.102 WRITE DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.102 SET FEATURES [Enable SATA feature] Error 403 [18] occurred at disk power-on lifetime: 6127 hours (255 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.112 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:06:18.111 IDENTIFY DEVICE ca 00 00 00 08 00 00 00 00 21 47 e0 08 00:06:18.102 WRITE DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:06:18.102 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:06:18.101 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 7616 - # 2 Extended offline Completed without error 00% 7455 - # 3 Extended offline Completed without error 00% 7278 - # 4 Extended offline Completed without error 00% 7108 - # 5 Extended offline Completed without error 00% 7065 - # 6 Extended offline Completed without error 00% 6989 - # 7 Extended offline Completed without error 00% 6928 - # 8 Extended offline Completed without error 00% 6834 - # 9 Extended offline Completed without error 00% 6770 - #10 Extended offline Interrupted (host reset) 70% 5848 - #11 Extended offline Completed without error 00% 5412 - #12 Extended offline Completed without error 00% 5196 - #13 Extended offline Completed without error 00% 4692 - #14 Extended offline Completed without error 00% 4398 - #15 Extended offline Completed without error 00% 4339 - #16 Extended offline Completed without error 00% 4036 - #17 Extended offline Completed without error 00% 3948 - #18 Extended offline Completed without error 00% 3914 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 25/27 Celsius Lifetime Min/Max Temperature: 14/46 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (17) Index Estimated Time Temperature Celsius 18 2017-01-13 07:57 30 *********** ... ..( 76 skipped). .. *********** 95 2017-01-13 09:14 30 *********** 96 2017-01-13 09:15 31 ************ ... ..( 2 skipped). .. ************ 99 2017-01-13 09:18 31 ************ 100 2017-01-13 09:19 32 ************* ... ..( 2 skipped). .. ************* 103 2017-01-13 09:22 32 ************* 104 2017-01-13 09:23 33 ************** ... ..( 4 skipped). .. ************** 109 2017-01-13 09:28 33 ************** 110 2017-01-13 09:29 34 *************** ... ..( 13 skipped). .. *************** 124 2017-01-13 09:43 34 *************** 125 2017-01-13 09:44 35 **************** ... ..( 67 skipped). .. **************** 193 2017-01-13 10:52 35 **************** 194 2017-01-13 10:53 34 *************** 195 2017-01-13 10:54 35 **************** ... ..( 7 skipped). .. **************** 203 2017-01-13 11:02 35 **************** 204 2017-01-13 11:03 34 *************** 205 2017-01-13 11:04 35 **************** 206 2017-01-13 11:05 34 *************** ... ..( 12 skipped). .. *************** 219 2017-01-13 11:18 34 *************** 220 2017-01-13 11:19 ? - 221 2017-01-13 11:20 21 ** 222 2017-01-13 11:21 21 ** 223 2017-01-13 11:22 22 *** 224 2017-01-13 11:23 22 *** 225 2017-01-13 11:24 23 **** 226 2017-01-13 11:25 24 ***** 227 2017-01-13 11:26 24 ***** 228 2017-01-13 11:27 25 ****** 229 2017-01-13 11:28 25 ****** 230 2017-01-13 11:29 26 ******* 231 2017-01-13 11:30 26 ******* 232 2017-01-13 11:31 26 ******* 233 2017-01-13 11:32 27 ******** 234 2017-01-13 11:33 27 ******** 235 2017-01-13 11:34 27 ******** 236 2017-01-13 11:35 28 ********* ... ..( 9 skipped). .. ********* 246 2017-01-13 11:45 28 ********* 247 2017-01-13 11:46 ? - 248 2017-01-13 11:47 21 ** 249 2017-01-13 11:48 ? - 250 2017-01-13 11:49 34 *************** 251 2017-01-13 11:50 ? - 252 2017-01-13 11:51 34 *************** 253 2017-01-13 11:52 34 *************** 254 2017-01-13 11:53 ? - 255 2017-01-13 11:54 33 ************** ... ..( 3 skipped). .. ************** 259 2017-01-13 11:58 33 ************** 260 2017-01-13 11:59 34 *************** ... ..( 12 skipped). .. *************** 273 2017-01-13 12:12 34 *************** 274 2017-01-13 12:13 35 **************** ... ..( 12 skipped). .. **************** 287 2017-01-13 12:26 35 **************** 288 2017-01-13 12:27 ? - 289 2017-01-13 12:28 36 ***************** ... ..( 6 skipped). .. ***************** 296 2017-01-13 12:35 36 ***************** 297 2017-01-13 12:36 ? - 298 2017-01-13 12:37 36 ***************** 299 2017-01-13 12:38 35 **************** 300 2017-01-13 12:39 35 **************** 301 2017-01-13 12:40 ? - 302 2017-01-13 12:41 35 **************** 303 2017-01-13 12:42 35 **************** 304 2017-01-13 12:43 ? - 305 2017-01-13 12:44 35 **************** ... ..( 41 skipped). .. **************** 347 2017-01-13 13:26 35 **************** 348 2017-01-13 13:27 ? - 349 2017-01-13 13:28 35 **************** 350 2017-01-13 13:29 ? - 351 2017-01-13 13:30 21 ** 352 2017-01-13 13:31 ? - 353 2017-01-13 13:32 22 *** 354 2017-01-13 13:33 23 **** 355 2017-01-13 13:34 23 **** 356 2017-01-13 13:35 ? - 357 2017-01-13 13:36 24 ***** 358 2017-01-13 13:37 ? - 359 2017-01-13 13:38 25 ****** 360 2017-01-13 13:39 26 ******* 361 2017-01-13 13:40 ? - 362 2017-01-13 13:41 25 ****** 363 2017-01-13 13:42 25 ****** 364 2017-01-13 13:43 26 ******* 365 2017-01-13 13:44 26 ******* 366 2017-01-13 13:45 26 ******* 367 2017-01-13 13:46 27 ******** 368 2017-01-13 13:47 30 *********** ... ..(126 skipped). .. *********** 17 2017-01-13 15:54 30 *********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 376 Vendor specific /dev/sdd === START OF INFORMATION SECTION === Device Model: INTENSO SSD 128GB Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: O0213E User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jan 13 15:54:51 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Disabled Write cache is: Enabled ATA Security is: Unavailable Read SCT Status failed: scsi error badly formed scsi parameters Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate ------ 100 100 050 - 0 5 Reallocated_Sector_Ct -O---- 100 100 050 - 0 9 Power_On_Hours ------ 100 100 050 - 0 12 Power_Cycle_Count ------ 100 100 050 - 4 160 Unknown_Attribute ------ 100 100 050 - 0 161 Unknown_Attribute ------ 100 100 050 - 255 162 Unknown_Attribute ------ 100 100 050 - 0 163 Unknown_Attribute ------ 100 100 050 - 81 164 Unknown_Attribute ------ 100 100 050 - 11 165 Unknown_Attribute ------ 100 100 050 - 1 166 Unknown_Attribute ------ 100 100 050 - 0 167 Unknown_Attribute ------ 100 100 050 - 0 192 Power-Off_Retract_Count ------ 100 100 050 - 4 194 Temperature_Celsius ------ 100 100 050 - 26 195 Hardware_ECC_Recovered ------ 100 100 050 - 0 196 Reallocated_Event_Count ------ 100 100 050 - 0 199 UDMA_CRC_Error_Count ------ 100 100 050 - 0 241 Total_LBAs_Written ------ 100 100 050 - 0 242 Total_LBAs_Read ------ 100 100 050 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Read SCT Status failed: scsi error badly formed scsi parameters Read SCT Status failed: scsi error badly formed scsi parameters SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 4 --- Lifetime Power-On Resets 0x01 0x010 4 0 --- Power-on Hours 0x01 0x018 6 0 --- Logical Sectors Written 0x01 0x020 6 0 --- Number of Write Commands 0x01 0x028 6 0 --- Logical Sectors Read 0x01 0x030 6 163 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (empty) == 0x03 ===== = = === == Rotating Media Statistics (empty) == 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 4 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 26 --- Current Temperature 0x05 0x010 1 0 --- Average Short Term Temperature 0x05 0x018 1 0 --- Average Long Term Temperature 0x05 0x020 1 19 --- Highest Temperature 0x05 0x028 1 19 --- Lowest Temperature 0x05 0x030 1 19 --- Highest Average Short Term Temperature 0x05 0x038 1 19 --- Lowest Average Short Term Temperature 0x05 0x040 1 19 --- Highest Average Long Term Temperature 0x05 0x048 1 19 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 100 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 9 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC