/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Momentus SpinPoint M8 (AF) Device Model: ST500LM012 HN-M500MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2AR10002 User Capacity: 500 107 862 016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Mar 16 20:56:16 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6660) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 111) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 47 2 Throughput_Performance POS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 091 091 025 - 2854 4 Start_Stop_Count -O--CK 100 100 000 - 614 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate POSR-K 252 252 051 - 0 8 Seek_Time_Performance P-S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 1188 10 Spin_Retry_Count PO--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 5 12 Power_Cycle_Count -O--CK 100 100 000 - 626 181 Program_Fail_Cnt_Total -O---K 100 100 000 - 8545098 183 Runtime_Bad_Block -O--CK 252 252 010 - 0 184 End-to-End_Error PO--CK 252 252 048 - 0 186 Unknown_Attribute -O--CK 252 252 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 36 188 Command_Timeout -O--CK 252 252 000 - 0 190 Airflow_Temperature_Cel -O---- 059 050 040 - 41 (Min/Max 12/51) 191 G-Sense_Error_Rate -O---K 100 100 000 - 47 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 193 Load_Cycle_Count -O--CK 098 098 000 - 25888 194 Temperature_Celsius -O---- 059 050 000 - 41 (Min/Max 12/51) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 100 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 6830 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 36 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 36 [3] occurred at disk power-on lifetime: 1123 hours (46 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 02 f1 2c 28 40 00 Error: UNC at LBA = 0x02f12c28 = 49359912 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.144 READ FPDMA QUEUED 60 00 02 00 04 00 00 00 00 08 40 40 00 00:00:00.266 READ FPDMA QUEUED 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.266 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.266 SET FEATURES [Enable write cache] 00 20 20 00 01 00 00 00 00 08 00 40 00 00:00:00.266 NOP [Reserved subcommand] [OBS-ACS-2] Error 35 [2] occurred at disk power-on lifetime: 1123 hours (46 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 02 f1 2c 28 40 00 Error: UNC at LBA = 0x02f12c28 = 49359912 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.142 READ FPDMA QUEUED 60 00 02 00 04 00 00 00 00 08 40 40 00 00:00:00.264 READ FPDMA QUEUED 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.264 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.264 SET FEATURES [Enable write cache] 00 20 20 00 01 00 00 00 00 08 00 40 00 00:00:00.264 NOP [Reserved subcommand] [OBS-ACS-2] Error 34 [1] occurred at disk power-on lifetime: 1123 hours (46 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 02 f1 2c 28 40 00 Error: UNC at LBA = 0x02f12c28 = 49359912 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.139 READ FPDMA QUEUED 60 00 02 00 04 00 00 00 00 08 40 40 00 00:00:00.261 READ FPDMA QUEUED 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.261 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.261 SET FEATURES [Enable write cache] 00 20 20 00 01 00 00 00 00 08 00 40 00 00:00:00.261 NOP [Reserved subcommand] [OBS-ACS-2] Error 33 [0] occurred at disk power-on lifetime: 1123 hours (46 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 02 f1 2c 28 40 00 Error: UNC at LBA = 0x02f12c28 = 49359912 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.137 READ FPDMA QUEUED 60 00 02 00 04 00 00 00 00 08 40 40 00 00:00:00.259 READ FPDMA QUEUED 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.259 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.259 SET FEATURES [Enable write cache] 00 20 20 00 01 00 00 00 00 08 00 40 00 00:00:00.259 NOP [Reserved subcommand] [OBS-ACS-2] Error 32 [7] occurred at disk power-on lifetime: 1123 hours (46 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 02 f1 2c 28 40 00 Error: UNC at LBA = 0x02f12c28 = 49359912 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.134 READ FPDMA QUEUED 60 00 02 00 04 00 00 00 00 08 40 40 00 00:00:00.256 READ FPDMA QUEUED 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.256 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.256 SET FEATURES [Enable write cache] 00 20 20 00 01 00 00 00 00 08 00 40 00 00:00:00.256 NOP [Reserved subcommand] [OBS-ACS-2] Error 31 [6] occurred at disk power-on lifetime: 1123 hours (46 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 02 f1 2c 28 40 00 Error: UNC at LBA = 0x02f12c28 = 49359912 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.132 READ FPDMA QUEUED 60 00 02 00 04 00 00 00 00 08 40 40 00 00:00:00.254 READ FPDMA QUEUED 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.254 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.254 SET FEATURES [Enable write cache] 00 20 20 00 01 00 00 00 00 08 00 40 00 00:00:00.254 NOP [Reserved subcommand] [OBS-ACS-2] Error 30 [5] occurred at disk power-on lifetime: 1123 hours (46 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 02 f1 2c 28 40 00 Error: UNC at LBA = 0x02f12c28 = 49359912 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.129 READ FPDMA QUEUED 60 00 02 00 04 00 00 00 00 08 40 40 00 00:00:00.251 READ FPDMA QUEUED 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.251 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.251 SET FEATURES [Enable write cache] 00 20 20 00 01 00 00 00 00 08 00 40 00 00:00:00.251 NOP [Reserved subcommand] [OBS-ACS-2] Error 29 [4] occurred at disk power-on lifetime: 1123 hours (46 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 02 f1 2c 28 40 00 Error: UNC at LBA = 0x02f12c28 = 49359912 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.127 READ FPDMA QUEUED 60 00 02 00 04 00 00 00 00 08 40 40 00 00:00:00.249 READ FPDMA QUEUED 60 00 02 00 08 00 00 02 f1 2c 28 40 00 00:00:00.249 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.249 SET FEATURES [Enable write cache] 00 20 20 00 01 00 00 00 00 08 00 40 00 00:00:00.248 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 597 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 39/42 Celsius Lifetime Min/Max Temperature: 12/51 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (14) Index Estimated Time Temperature Celsius 15 2016-03-16 10:20 41 ********************** 16 2016-03-16 10:25 32 ************* ... ..( 14 skipped). .. ************* 31 2016-03-16 11:40 32 ************* 32 2016-03-16 11:45 33 ************** 33 2016-03-16 11:50 33 ************** 34 2016-03-16 11:55 32 ************* ... ..( 3 skipped). .. ************* 38 2016-03-16 12:15 32 ************* 39 2016-03-16 12:20 33 ************** ... ..( 25 skipped). .. ************** 65 2016-03-16 14:30 33 ************** 66 2016-03-16 14:35 25 ****** 67 2016-03-16 14:40 29 ********** 68 2016-03-16 14:45 32 ************* 69 2016-03-16 14:50 33 ************** 70 2016-03-16 14:55 34 *************** 71 2016-03-16 15:00 36 ***************** 72 2016-03-16 15:05 37 ****************** 73 2016-03-16 15:10 38 ******************* 74 2016-03-16 15:15 39 ******************** 75 2016-03-16 15:20 40 ********************* 76 2016-03-16 15:25 41 ********************** 77 2016-03-16 15:30 37 ****************** 78 2016-03-16 15:35 38 ******************* ... ..( 3 skipped). .. ******************* 82 2016-03-16 15:55 38 ******************* 83 2016-03-16 16:00 39 ******************** ... ..( 3 skipped). .. ******************** 87 2016-03-16 16:20 39 ******************** 88 2016-03-16 16:25 27 ******** 89 2016-03-16 16:30 29 ********** 90 2016-03-16 16:35 32 ************* 91 2016-03-16 16:40 34 *************** 92 2016-03-16 16:45 36 ***************** 93 2016-03-16 16:50 39 ******************** ... ..( 4 skipped). .. ******************** 98 2016-03-16 17:15 39 ******************** 99 2016-03-16 17:20 40 ********************* 100 2016-03-16 17:25 40 ********************* 101 2016-03-16 17:30 39 ******************** ... ..( 5 skipped). .. ******************** 107 2016-03-16 18:00 39 ******************** 108 2016-03-16 18:05 40 ********************* 109 2016-03-16 18:10 40 ********************* 110 2016-03-16 18:15 39 ******************** 111 2016-03-16 18:20 38 ******************* ... ..( 3 skipped). .. ******************* 115 2016-03-16 18:40 38 ******************* 116 2016-03-16 18:45 36 ***************** 117 2016-03-16 18:50 37 ****************** 118 2016-03-16 18:55 38 ******************* ... ..( 3 skipped). .. ******************* 122 2016-03-16 19:15 38 ******************* 123 2016-03-16 19:20 39 ******************** ... ..( 3 skipped). .. ******************** 127 2016-03-16 19:40 39 ******************** 0 2016-03-16 19:45 38 ******************* 1 2016-03-16 19:50 39 ******************** ... ..( 3 skipped). .. ******************** 5 2016-03-16 20:10 39 ******************** 6 2016-03-16 20:15 40 ********************* ... ..( 4 skipped). .. ********************* 11 2016-03-16 20:40 40 ********************* 12 2016-03-16 20:45 41 ********************** 13 2016-03-16 20:50 42 *********************** 14 2016-03-16 20:55 42 *********************** SCT Error Recovery Control: Read: 85 (8,5 seconds) Write: 85 (8,5 seconds) Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 1 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific