/dev/nvme0n1 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-60-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: Samsung SSD 990 PRO 2TB Serial Number: -- Firmware Version: 4B2QJXD7 PCI Vendor/Subsystem ID: 0x144d IEEE OUI Identifier: 0x002538 Total NVM Capacity: 2,000,398,934,016 [2.00 TB] Unallocated NVM Capacity: 0 Controller ID: 1 NVMe Version: 2.0 Number of Namespaces: 1 Namespace 1 Size/Capacity: 2,000,398,934,016 [2.00 TB] Namespace 1 Utilization: 372,288,884,736 [372 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 002538 ... Local Time is: Sun May 18 20:17:32 2025 CDT Firmware Updates (0x16): 3 Slots, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x0055): Comp DS_Mngmt Sav/Sel_Feat Timestmp Log Page Attributes (0x2f): S/H_per_NS Cmd_Eff_Lg Ext_Get_Lg Telmtry_Lg Log0_FISE_MI Maximum Data Transfer Size: 512 Pages Warning Comp. Temp. Threshold: 82 Celsius Critical Comp. Temp. Threshold: 85 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 9.39W - - 0 0 0 0 0 0 1 + 9.39W - - 1 1 1 1 0 0 2 + 9.39W - - 2 2 2 2 0 0 3 - 0.0400W - - 3 3 3 3 4200 2700 4 - 0.0050W - - 4 4 4 4 500 21800 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 47 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 0% Data Units Read: 4,038,863 [2.06 TB] Data Units Written: 4,604,911 [2.35 TB] Host Read Commands: 36,196,220 Host Write Commands: 73,635,505 Controller Busy Time: 188 Power Cycles: 36 Power On Hours: 944 Unsafe Shutdowns: 30 Media and Data Integrity Errors: 0 Error Information Log Entries: 0 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 47 Celsius Temperature Sensor 2: 50 Celsius Error Information (NVMe Log 0x01, 16 of 64 entries) No Errors Logged Read Self-test Log failed: Invalid Field in Command (0x002) /dev/nvme1n1 smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-60-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: CT500P310SSD8 Serial Number: -- Firmware Version: V8CR000 PCI Vendor/Subsystem ID: 0xc0a9 IEEE OUI Identifier: 0x00a075 Controller ID: 0 NVMe Version: 1.4 Number of Namespaces: 1 Namespace 1 Size/Capacity: 500,107,862,016 [500 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 00a075 ... Local Time is: Sun May 18 20:17:32 2025 CDT Firmware Updates (0x14): 2 Slots, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x00d7): Comp Wr_Unc DS_Mngmt Sav/Sel_Feat Timestmp Verify Log Page Attributes (0x1e): Cmd_Eff_Lg Ext_Get_Lg Telmtry_Lg Pers_Ev_Lg Maximum Data Transfer Size: 64 Pages Warning Comp. Temp. Threshold: 86 Celsius Critical Comp. Temp. Threshold: 88 Celsius Namespace 1 Features (0x18): No_ID_Reuse NP_Fields Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 6.30W - - 0 0 0 0 0 0 1 + 2.40W - - 1 1 1 1 0 0 2 + 1.50W - - 2 2 2 2 0 0 3 - 0.0300W - - 3 3 3 3 1500 3500 4 - 0.0025W - - 4 4 4 4 5000 30000 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 1 - 4096 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 39 Celsius Available Spare: 100% Available Spare Threshold: 5% Percentage Used: 0% Data Units Read: 13,303 [6.81 GB] Data Units Written: 70,542 [36.1 GB] Host Read Commands: 180,628 Host Write Commands: 505,938 Controller Busy Time: 0 Power Cycles: 8 Power On Hours: 233 Unsafe Shutdowns: 7 Media and Data Integrity Errors: 0 Error Information Log Entries: 0 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 39 Celsius Error Information (NVMe Log 0x01, 16 of 255 entries) No Errors Logged Read Self-test Log failed: Invalid Field in Command (0x002) /dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-60-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: T-FORCE 2TB Serial Number: -- Firmware Version: V0718B0 User Capacity: 2,048,408,248,320 bytes [2.04 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database 7.3/5528 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 18 20:17:32 2025 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SCT capabilities: (0x0001) SCT Status supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0 9 Power_On_Hours -O--CK 100 100 050 - 19577 12 Power_Cycle_Count -O--CK 100 100 050 - 93 160 Unknown_Attribute -O--CK 100 100 050 - 0 161 Unknown_Attribute PO--CK 100 100 050 - 100 163 Unknown_Attribute -O--CK 100 100 050 - 11 164 Unknown_Attribute -O--CK 100 100 050 - 25427 165 Unknown_Attribute -O--CK 100 100 050 - 56 166 Unknown_Attribute -O--CK 100 100 050 - 16 167 Unknown_Attribute -O--CK 100 100 050 - 28 168 Unknown_Attribute -O--CK 100 100 050 - 5050 169 Unknown_Attribute -O--CK 100 100 050 - 100 175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 0 177 Wear_Leveling_Count -O--CK 100 100 050 - 0 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0 192 Power-Off_Retract_Count -O--CK 100 100 050 - 65 194 Temperature_Celsius -O---K 100 100 050 - 21 195 Hardware_ECC_Recovered -O--CK 100 100 050 - 0 196 Reallocated_Event_Count -O--CK 100 100 050 - 0 197 Current_Pending_Sector -O--CK 100 100 050 - 0 198 Offline_Uncorrectable -O--CK 100 100 050 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 0 232 Available_Reservd_Space -O--CK 100 100 050 - 100 241 Total_LBAs_Written ----CK 100 100 050 - 513598 242 Total_LBAs_Read ----CK 100 100 050 - 484296 245 Unknown_Attribute -O--CK 100 100 050 - 441504 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 32 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 21 Celsius Power Cycle Min/Max Temperature: 21/21 Celsius Lifetime Min/Max Temperature: 13/41 Celsius Specified Max Operating Temperature: 100 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 93 --- Lifetime Power-On Resets 0x01 0x010 4 19577 --- Power-on Hours 0x01 0x018 6 3594450946 --- Logical Sectors Written 0x01 0x020 6 151982747 --- Number of Write Commands 0x01 0x028 6 1674080051 --- Logical Sectors Read 0x01 0x030 6 153795298 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 5 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-60-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ADATA SU635 Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: V8X14c18 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database 7.3/5528 ATA Version is: ACS-3, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 18 20:17:32 2025 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Disabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1) seconds. Offline data collection capabilities: (0x59) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 7) minutes. Extended self-test routine recommended polling time: ( 23) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 36471 12 Power_Cycle_Count -O--CK 100 100 000 - 131 161 Unknown_Attribute -O--CK 100 100 000 - 45 162 Unknown_Attribute -O--CK 100 100 000 - 46482 163 Unknown_Attribute -O--CK 100 100 000 - 3000 164 Unknown_Attribute -O--CK 100 100 000 - 33 166 Unknown_Attribute -O--CK 100 100 000 - 71 167 Unknown_Attribute -O--CK 100 100 050 - 0 168 Unknown_Attribute -O--CK 100 100 000 - 0 169 Unknown_Attribute -O--CK 100 100 000 - 98 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 174 Unknown_Attribute -O--CK 100 100 000 - 82 175 Program_Fail_Count_Chip -O--CK 100 100 000 - 0 181 Program_Fail_Cnt_Total -O---K 100 100 000 - 142177 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 030 - 35 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 85713 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 206 Unknown_SSD_Attribute -O--CK 100 100 000 - 16 207 Unknown_SSD_Attribute -O--CK 100 100 000 - 40 232 Available_Reservd_Space -O--CK 100 100 000 - 97 233 Media_Wearout_Indicator -O--CK 100 100 000 - 1621 241 Total_LBAs_Written -O--CK 100 100 000 - 5181 242 Total_LBAs_Read -O--CK 100 100 000 - 6060 249 Unknown_Attribute -O--CK 100 100 000 - 3540 250 Read_Error_Retry_Rate -O--CK 100 100 000 - 5466 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 5 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: 28/28 Celsius Lifetime Min/Max Temperature: 0/36 Celsius Specified Max Operating Temperature: 100 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 0 minutes Temperature Logging Interval: 0 minutes Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: -10/125 Celsius Temperature History Size (Index): 128 (1) Index Estimated Time Temperature Celsius 2 2025-05-18 18:10 ? - ... ..(124 skipped). .. - 127 2025-05-18 20:15 ? - 0 2025-05-18 20:16 36 ***************** 1 2025-05-18 20:17 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 131 --- Lifetime Power-On Resets 0x01 0x010 4 36471 --- Power-on Hours 0x01 0x018 6 10865659832 --- Logical Sectors Written 0x01 0x020 6 67005279 --- Number of Write Commands 0x01 0x028 6 12708986860 --- Logical Sectors Read 0x01 0x030 6 73783803 --- Number of Read Commands 0x01 0x038 6 131296722381 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1 --- Resets Between Cmd Acceptance and Completion 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 13032 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 2 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 6 Device-to-host register FISes sent due to a COMRESET /dev/sdc smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.8.0-60-generic] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: T-FORCE 1TB Serial Number: -- Firmware Version: X0826A0 User Capacity: 1,024,209,543,168 bytes [1.02 TB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database 7.3/5528 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun May 18 20:17:35 2025 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SCT capabilities: (0x0001) SCT Status supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0 9 Power_On_Hours -O--CK 100 100 050 - 790 12 Power_Cycle_Count -O--CK 100 100 050 - 25 160 Unknown_Attribute -O--CK 100 100 050 - 0 161 Unknown_Attribute PO--CK 100 100 050 - 100 163 Unknown_Attribute -O--CK 100 100 050 - 34 164 Unknown_Attribute -O--CK 100 100 050 - 4948 165 Unknown_Attribute -O--CK 100 100 050 - 5 166 Unknown_Attribute -O--CK 100 100 050 - 1 167 Unknown_Attribute -O--CK 100 100 050 - 3 168 Unknown_Attribute -O--CK 100 100 050 - 5050 169 Unknown_Attribute -O--CK 100 100 050 - 100 175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 0 177 Wear_Leveling_Count -O--CK 100 100 050 - 0 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0 192 Power-Off_Retract_Count -O--CK 100 100 050 - 20 194 Temperature_Celsius -O---K 100 100 050 - 17 195 Hardware_ECC_Recovered -O--CK 100 100 050 - 0 196 Reallocated_Event_Count -O--CK 100 100 050 - 0 197 Current_Pending_Sector -O--CK 100 100 050 - 0 198 Offline_Uncorrectable -O--CK 100 100 050 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 0 232 Available_Reservd_Space -O--CK 100 100 050 - 100 241 Total_LBAs_Written ----CK 100 100 050 - 31629 242 Total_LBAs_Read ----CK 100 100 050 - 20848 245 Unknown_Attribute -O--CK 100 100 050 - 20097 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 32 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 17 Celsius Power Cycle Min/Max Temperature: 17/17 Celsius Lifetime Min/Max Temperature: 17/32 Celsius Specified Max Operating Temperature: 100 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 25 --- Lifetime Power-On Resets 0x01 0x010 4 790 --- Power-on Hours 0x01 0x018 6 2072880685 --- Logical Sectors Written 0x01 0x020 6 8807823 --- Number of Write Commands 0x01 0x028 6 1366310147 --- Logical Sectors Read 0x01 0x030 6 6208405 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 5 Device-to-host register FISes sent due to a COMRESET