/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar 5K750 Device Model: Hitachi HTS547550A9E384 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JE3OA50B User Capacity: 500 107 862 016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Nov 27 22:26:03 2018 +04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 137) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 100 100 040 - 0 3 Spin_Up_Time POS--- 214 214 033 - 1 4 Start_Stop_Count -O--C- 100 100 000 - 624 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 0 9 Power_On_Hours -O--C- 098 098 000 - 902 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 587 160 Unknown_Attribute PO-RCK 100 100 001 - 0 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 88 193 Load_Cycle_Count -O--C- 093 093 000 - 74766 194 Temperature_Celsius -O---- 162 162 000 - 37 (Min/Max 11/45) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 192 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 34/37 Celsius Lifetime Min/Max Temperature: 11/45 Celsius Lifetime Average Temperature: 32 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (110) Index Estimated Time Temperature Celsius 111 2018-11-27 20:19 35 **************** ... ..( 9 skipped). .. **************** 121 2018-11-27 20:29 35 **************** 122 2018-11-27 20:30 ? - 123 2018-11-27 20:31 36 ***************** 124 2018-11-27 20:32 ? - ... ..( 3 skipped). .. - 0 2018-11-27 20:36 ? - 1 2018-11-27 20:37 38 ******************* 2 2018-11-27 20:38 39 ******************** 3 2018-11-27 20:39 39 ******************** 4 2018-11-27 20:40 ? - 5 2018-11-27 20:41 ? - 6 2018-11-27 20:42 39 ******************** 7 2018-11-27 20:43 40 ********************* 8 2018-11-27 20:44 40 ********************* 9 2018-11-27 20:45 40 ********************* 10 2018-11-27 20:46 ? - 11 2018-11-27 20:47 ? - 12 2018-11-27 20:48 40 ********************* 13 2018-11-27 20:49 ? - ... ..( 2 skipped). .. - 16 2018-11-27 20:52 ? - 17 2018-11-27 20:53 40 ********************* 18 2018-11-27 20:54 ? - 19 2018-11-27 20:55 39 ******************** 20 2018-11-27 20:56 38 ******************* ... ..( 4 skipped). .. ******************* 25 2018-11-27 21:01 38 ******************* 26 2018-11-27 21:02 39 ******************** ... ..( 6 skipped). .. ******************** 33 2018-11-27 21:09 39 ******************** 34 2018-11-27 21:10 38 ******************* ... ..( 4 skipped). .. ******************* 39 2018-11-27 21:15 38 ******************* 40 2018-11-27 21:16 37 ****************** 41 2018-11-27 21:17 37 ****************** 42 2018-11-27 21:18 ? - 43 2018-11-27 21:19 37 ****************** 44 2018-11-27 21:20 ? - 45 2018-11-27 21:21 37 ****************** 46 2018-11-27 21:22 37 ****************** 47 2018-11-27 21:23 36 ***************** 48 2018-11-27 21:24 36 ***************** 49 2018-11-27 21:25 36 ***************** 50 2018-11-27 21:26 ? - 51 2018-11-27 21:27 ? - 52 2018-11-27 21:28 36 ***************** ... ..( 3 skipped). .. ***************** 56 2018-11-27 21:32 36 ***************** 57 2018-11-27 21:33 35 **************** ... ..( 16 skipped). .. **************** 74 2018-11-27 21:50 35 **************** 75 2018-11-27 21:51 34 *************** 76 2018-11-27 21:52 34 *************** 77 2018-11-27 21:53 35 **************** 78 2018-11-27 21:54 ? - 79 2018-11-27 21:55 35 **************** ... ..( 16 skipped). .. **************** 96 2018-11-27 22:12 35 **************** 97 2018-11-27 22:13 34 *************** 98 2018-11-27 22:14 35 **************** 99 2018-11-27 22:15 35 **************** 100 2018-11-27 22:16 35 **************** 101 2018-11-27 22:17 36 ***************** 102 2018-11-27 22:18 36 ***************** 103 2018-11-27 22:19 36 ***************** 104 2018-11-27 22:20 37 ****************** ... ..( 5 skipped). .. ****************** 110 2018-11-27 22:26 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 43 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 36 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS