/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-00BN5A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Feb 8 07:50:33 2017 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11280) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 117) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1579 3 Spin_Up_Time POS--K 174 171 021 - 2283 4 Start_Stop_Count -O--CK 099 099 000 - 1238 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 094 094 000 - 4683 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1234 192 Power-Off_Retract_Count -O--CK 200 200 000 - 54 193 Load_Cycle_Count -O--CK 200 200 000 - 1184 194 Temperature_Celsius -O---K 107 097 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1576 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1576 [15] occurred at disk power-on lifetime: 2289 hours (95 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3c 37 e0 40 00 Error: UNC at LBA = 0x023c37e0 = 37500896 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 58 00 00 02 3c 37 e0 40 00 00:39:23.732 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:39:23.732 SET FEATURES [Enable write cache] 60 00 08 00 50 00 00 02 3c 37 d8 40 00 00:39:20.016 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:39:20.016 SET FEATURES [Enable write cache] 60 00 08 00 48 00 00 02 3c 37 d0 40 00 00:39:15.307 READ FPDMA QUEUED Error 1575 [14] occurred at disk power-on lifetime: 2289 hours (95 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3c 37 d8 40 00 Error: UNC at LBA = 0x023c37d8 = 37500888 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 50 00 00 02 3c 37 d8 40 00 00:39:20.016 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:39:20.016 SET FEATURES [Enable write cache] 60 00 08 00 48 00 00 02 3c 37 d0 40 00 00:39:15.307 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:39:15.223 SET FEATURES [Enable write cache] 60 00 08 00 40 00 00 02 3c 37 c8 40 00 00:39:11.344 READ FPDMA QUEUED Error 1574 [13] occurred at disk power-on lifetime: 2289 hours (95 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3c 37 d0 40 00 Error: UNC at LBA = 0x023c37d0 = 37500880 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 48 00 00 02 3c 37 d0 40 00 00:39:15.307 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:39:15.223 SET FEATURES [Enable write cache] 60 00 08 00 40 00 00 02 3c 37 c8 40 00 00:39:11.344 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:39:11.265 SET FEATURES [Enable write cache] 60 00 08 00 38 00 00 02 3c 37 c0 40 00 00:39:07.382 READ FPDMA QUEUED Error 1573 [12] occurred at disk power-on lifetime: 2289 hours (95 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3c 37 c8 40 00 Error: UNC at LBA = 0x023c37c8 = 37500872 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 02 3c 37 c8 40 00 00:39:11.344 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:39:11.265 SET FEATURES [Enable write cache] 60 00 08 00 38 00 00 02 3c 37 c0 40 00 00:39:07.382 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:39:07.290 SET FEATURES [Enable write cache] 60 00 08 00 30 00 00 02 3c 37 b8 40 00 00:39:03.519 READ FPDMA QUEUED Error 1572 [11] occurred at disk power-on lifetime: 2289 hours (95 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3c 37 c0 40 00 Error: UNC at LBA = 0x023c37c0 = 37500864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 38 00 00 02 3c 37 c0 40 00 00:39:07.382 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:39:07.290 SET FEATURES [Enable write cache] 60 00 08 00 30 00 00 02 3c 37 b8 40 00 00:39:03.519 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:39:03.425 SET FEATURES [Enable write cache] 60 00 08 00 28 00 00 02 3c 37 b0 40 00 00:38:59.681 READ FPDMA QUEUED Error 1571 [10] occurred at disk power-on lifetime: 2289 hours (95 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3c 37 b8 40 00 Error: UNC at LBA = 0x023c37b8 = 37500856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 30 00 00 02 3c 37 b8 40 00 00:39:03.519 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:39:03.425 SET FEATURES [Enable write cache] 60 00 08 00 28 00 00 02 3c 37 b0 40 00 00:38:59.681 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:38:59.601 SET FEATURES [Enable write cache] 60 00 08 00 20 00 00 02 3c 37 a8 40 00 00:38:55.062 READ FPDMA QUEUED Error 1570 [9] occurred at disk power-on lifetime: 2289 hours (95 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3c 37 b0 40 00 Error: UNC at LBA = 0x023c37b0 = 37500848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 28 00 00 02 3c 37 b0 40 00 00:38:59.681 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:38:59.601 SET FEATURES [Enable write cache] 60 00 08 00 20 00 00 02 3c 37 a8 40 00 00:38:55.062 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:38:55.062 SET FEATURES [Enable write cache] 60 00 08 00 18 00 00 02 3c 37 a0 40 00 00:38:50.526 READ FPDMA QUEUED Error 1569 [8] occurred at disk power-on lifetime: 2289 hours (95 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 3c 37 a8 40 00 Error: UNC at LBA = 0x023c37a8 = 37500840 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 20 00 00 02 3c 37 a8 40 00 00:38:55.062 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:38:55.062 SET FEATURES [Enable write cache] 60 00 08 00 18 00 00 02 3c 37 a0 40 00 00:38:50.526 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 a0 00 00:38:50.525 SET FEATURES [Enable write cache] 60 00 08 00 10 00 00 02 3c 37 98 40 00 00:38:46.598 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 4611 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 24/36 Celsius Lifetime Min/Max Temperature: 20/46 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (435) Index Estimated Time Temperature Celsius 436 2017-02-07 23:53 37 ****************** ... ..( 10 skipped). .. ****************** 447 2017-02-08 00:04 37 ****************** 448 2017-02-08 00:05 ? - 449 2017-02-08 00:06 24 ***** 450 2017-02-08 00:07 24 ***** 451 2017-02-08 00:08 25 ****** 452 2017-02-08 00:09 25 ****** 453 2017-02-08 00:10 26 ******* 454 2017-02-08 00:11 27 ******** 455 2017-02-08 00:12 27 ******** 456 2017-02-08 00:13 28 ********* 457 2017-02-08 00:14 28 ********* 458 2017-02-08 00:15 29 ********** 459 2017-02-08 00:16 29 ********** 460 2017-02-08 00:17 30 *********** 461 2017-02-08 00:18 30 *********** 462 2017-02-08 00:19 30 *********** 463 2017-02-08 00:20 31 ************ 464 2017-02-08 00:21 31 ************ 465 2017-02-08 00:22 31 ************ 466 2017-02-08 00:23 32 ************* ... ..( 3 skipped). .. ************* 470 2017-02-08 00:27 32 ************* 471 2017-02-08 00:28 33 ************** ... ..( 3 skipped). .. ************** 475 2017-02-08 00:32 33 ************** 476 2017-02-08 00:33 34 *************** ... ..( 5 skipped). .. *************** 4 2017-02-08 00:39 34 *************** 5 2017-02-08 00:40 35 **************** ... ..( 19 skipped). .. **************** 25 2017-02-08 01:00 35 **************** 26 2017-02-08 01:01 36 ***************** ... ..(130 skipped). .. ***************** 157 2017-02-08 03:12 36 ***************** 158 2017-02-08 03:13 37 ****************** ... ..(162 skipped). .. ****************** 321 2017-02-08 05:56 37 ****************** 322 2017-02-08 05:57 38 ******************* ... ..( 22 skipped). .. ******************* 345 2017-02-08 06:20 38 ******************* 346 2017-02-08 06:21 37 ****************** ... ..( 15 skipped). .. ****************** 362 2017-02-08 06:37 37 ****************** 363 2017-02-08 06:38 38 ******************* ... ..( 31 skipped). .. ******************* 395 2017-02-08 07:10 38 ******************* 396 2017-02-08 07:11 37 ****************** ... ..( 38 skipped). .. ****************** 435 2017-02-08 07:50 37 ****************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 7 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 11247 Vendor specific