/dev/sda smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.47-generic-2rosa13-x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SPCC Solid State Disk Serial Number: -- LU WWN Device Id: 5 02b2a2 ... Add. Product Id: mavlsata Firmware Version: V4.9 User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available Device is: Not in smartctl database 7.5/5706 ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Oct 4 08:30:48 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x35) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x00) Error logging NOT supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 1) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 5 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours PO--CK 100 100 010 - 5033 12 Power_Cycle_Count PO--CK 100 100 010 - 4032 161 Unknown_Attribute PO--CK 100 100 010 - 0 164 Unknown_Attribute PO--CK 100 100 010 - 33563 165 Unknown_Attribute PO--CK 100 100 010 - 75 166 Unknown_Attribute PO--CK 100 100 010 - 0 167 Unknown_Attribute PO--CK 100 100 010 - 70 169 Unknown_Attribute PO--CK 100 100 010 - 0 176 Erase_Fail_Count_Chip PO--CK 100 100 010 - 0 177 Wear_Leveling_Count PO--CK 100 100 010 - 0 178 Used_Rsvd_Blk_Cnt_Chip PO--CK 100 100 010 - 0 192 Power-Off_Retract_Count PO--CK 100 100 010 - 0 194 Temperature_Celsius PO--CK 100 100 010 - 48 195 Hardware_ECC_Recovered PO--CK 100 100 010 - 0 199 UDMA_CRC_Error_Count PO--CK 100 100 010 - 0 241 Total_LBAs_Written PO--CK 100 100 010 - 9464 242 Total_LBAs_Read PO--CK 100 100 010 - 14734 243 Unknown_Attribute PO--CK 100 100 010 - 0 244 Unknown_Attribute PO--CK 100 100 010 - 0 245 Unknown_Attribute PO--CK 100 100 010 - 0 246 Unknown_Attribute PO--CK 100 100 010 - 0 248 Unknown_Attribute PO--CK 100 100 010 - 0 250 Read_Error_Retry_Rate PO--CK 100 100 010 - 0 251 Unknown_Attribute PO--CK 100 100 010 - 0 252 Unknown_Attribute PO--CK 100 100 010 - 0 253 Unknown_Attribute PO--CK 100 100 010 - 0 254 Unknown_SSD_Attribute PO--CK 100 100 010 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x10 GPL,SL R/O 1 NCQ Command Error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported Read SMART Error Log failed: scsi error aborted command SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test Log not supported Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdb smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.47-generic-2rosa13-x86_64] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar 5K750 Device Model: Hitachi HTS547575A9E384 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JE4OA50A User Capacity: 750,156,374,016 bytes [750 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.5/5706 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Oct 4 08:30:49 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 193) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 198 198 040 - 130 3 Spin_Up_Time POS--- 181 181 033 - 1 4 Start_Stop_Count -O--C- 091 091 000 - 15291 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 117 117 040 - 33 9 Power_On_Hours -O--C- 064 064 000 - 15789 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 092 092 000 - 13535 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 091 091 000 - 1918 193 Load_Cycle_Count -O--C- 012 012 000 - 888988 194 Temperature_Celsius -O---- 206 206 000 - 29 (Min/Max 16/56) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 17 hours (0 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 57 54 66 f0 07 00 Error: IDNF at LBA = 0x575466f0 = 1465149168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 08 00 00 57 54 66 f0 40 00 00:58:13.440 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 28 00 00:58:13.429 READ LOG EXT 60 00 01 00 00 00 00 57 54 66 f0 40 00 00:58:13.335 READ FPDMA QUEUED 60 00 01 00 00 00 00 00 00 00 01 40 00 00:58:13.335 READ FPDMA QUEUED 60 00 04 00 00 00 00 00 00 00 01 40 00 00:58:13.335 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 17 hours (0 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 57 54 66 f0 07 00 Error: IDNF at LBA = 0x575466f0 = 1465149168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 00 00 00 57 54 66 f0 40 00 00:58:13.335 READ FPDMA QUEUED 60 00 01 00 00 00 00 00 00 00 01 40 00 00:58:13.335 READ FPDMA QUEUED 60 00 04 00 00 00 00 00 00 00 01 40 00 00:58:13.335 READ FPDMA QUEUED 60 00 01 00 00 00 00 00 00 00 00 40 00 00:58:13.328 READ FPDMA QUEUED 60 00 30 00 00 00 00 01 80 45 ba 40 00 00:58:13.326 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 60% 7829 - # 2 Extended offline Interrupted (host reset) 50% 5631 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 23/30 Celsius Lifetime Min/Max Temperature: 16/56 Celsius Specified Max Operating Temperature: 33 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (80) Index Estimated Time Temperature Celsius 81 2025-10-04 06:23 28 ********* ... ..( 5 skipped). .. ********* 87 2025-10-04 06:29 28 ********* 88 2025-10-04 06:30 29 ********** 89 2025-10-04 06:31 28 ********* 90 2025-10-04 06:32 29 ********** ... ..( 13 skipped). .. ********** 104 2025-10-04 06:46 29 ********** 105 2025-10-04 06:47 30 *********** ... ..( 24 skipped). .. *********** 2 2025-10-04 07:12 30 *********** 3 2025-10-04 07:13 31 ************ 4 2025-10-04 07:14 31 ************ 5 2025-10-04 07:15 30 *********** 6 2025-10-04 07:16 31 ************ ... ..( 4 skipped). .. ************ 11 2025-10-04 07:21 31 ************ 12 2025-10-04 07:22 ? - 13 2025-10-04 07:23 23 **** 14 2025-10-04 07:24 24 ***** 15 2025-10-04 07:25 24 ***** 16 2025-10-04 07:26 25 ****** ... ..( 7 skipped). .. ****** 24 2025-10-04 07:34 25 ****** 25 2025-10-04 07:35 26 ******* ... ..( 6 skipped). .. ******* 32 2025-10-04 07:42 26 ******* 33 2025-10-04 07:43 27 ******** ... ..( 8 skipped). .. ******** 42 2025-10-04 07:52 27 ******** 43 2025-10-04 07:53 28 ********* ... ..( 12 skipped). .. ********* 56 2025-10-04 08:06 28 ********* 57 2025-10-04 08:07 29 ********** 58 2025-10-04 08:08 28 ********* 59 2025-10-04 08:09 29 ********** 60 2025-10-04 08:10 29 ********** 61 2025-10-04 08:11 29 ********** 62 2025-10-04 08:12 30 *********** 63 2025-10-04 08:13 29 ********** ... ..( 16 skipped). .. ********** 80 2025-10-04 08:30 29 ********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 13535 --- Lifetime Power-On Resets 0x01 0x010 4 15789 --- Power-on Hours 0x01 0x018 6 48286187867 --- Logical Sectors Written 0x01 0x020 6 552324928 --- Number of Write Commands 0x01 0x028 6 106778437454 --- Logical Sectors Read 0x01 0x030 6 1009420024 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 9664 --- Spindle Motor Power-on Hours 0x03 0x010 4 9597 --- Head Flying Hours 0x03 0x018 4 888989 --- Head Load Events 0x03 0x020 4 1 --- Number of Reallocated Logical Sectors 0x03 0x028 4 2764 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 2 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 16614 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 30 --- Current Temperature 0x05 0x010 1 28 N-- Average Short Term Temperature 0x05 0x018 1 26 N-- Average Long Term Temperature 0x05 0x020 1 56 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 42 N-- Highest Average Short Term Temperature 0x05 0x038 1 23 N-- Lowest Average Short Term Temperature 0x05 0x040 1 40 N-- Highest Average Long Term Temperature 0x05 0x048 1 24 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 101993 --- Number of Hardware Resets 0x06 0x010 4 11651 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 12395 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS