Probe #8302116452 of ASUSTek N56JN

Log: smartctl

/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.7-desktop-1omv4003] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST750LM022 HN-M750MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2BA30001 User Capacity: 750,156,374,016 bytes [750 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Mar 24 01:42:59 2022 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10200) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 170) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 4230 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 093 091 025 - 2327 4 Start_Stop_Count -O--CK 095 095 000 - 6044 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 8512 10 Spin_Retry_Count -O--CK 252 252 051 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 6034 191 G-Sense_Error_Rate -O---K 100 100 000 - 764 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 063 052 000 - 37 (Min/Max 14/48) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 100 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 11 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 13645 223 Load_Retry_Count -O--CK 095 095 000 - 5659 225 Load_Cycle_Count -O--CK 093 093 000 - 72594 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 4236 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4236 [3] occurred at disk power-on lifetime: 8486 hours (353 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 0a 00 00 07 4d 0f 10 40 00 Error: ICRC, ABRT 10 sectors at LBA = 0x074d0f10 = 122490640 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 0a 00 00 07 4d 0f 10 40 00 00:00:00.003 READ DMA EXT 25 00 00 00 40 00 00 0e 95 22 80 40 00 00:00:00.003 READ DMA EXT 25 00 00 00 40 00 00 02 a5 a9 80 40 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 40 00 00:00:00.003 READ DMA EXT 25 00 00 00 10 00 00 1d 3f 86 40 40 00 00:00:00.003 READ DMA EXT Error 4235 [2] occurred at disk power-on lifetime: 8437 hours (351 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 38 00 00 00 0a a6 40 40 00 Error: ICRC, ABRT 312 sectors at LBA = 0x000aa640 = 697920 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 00 0a 9f 78 40 00 00:00:00.011 READ DMA EXT 25 00 00 08 00 00 00 00 0a 97 78 40 00 00:00:00.011 READ DMA EXT 25 00 00 08 00 00 00 00 0a 8f 78 40 00 00:00:00.011 READ DMA EXT 25 00 00 08 00 00 00 00 0a 87 78 40 00 00:00:00.011 READ DMA EXT 25 00 00 08 00 00 00 00 0a 7f 78 40 00 00:00:00.011 READ DMA EXT Error 4234 [1] occurred at disk power-on lifetime: 8437 hours (351 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 04 98 00 00 00 10 61 80 40 00 Error: ICRC, ABRT 1176 sectors at LBA = 0x00106180 = 1073536 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 08 00 00 00 00 10 5e 18 40 00 00:00:00.017 READ DMA EXT 25 00 00 08 00 00 00 00 10 56 18 40 00 00:00:00.017 READ DMA EXT 25 00 00 08 00 00 00 00 10 4e 18 40 00 00:00:00.017 READ DMA EXT 25 00 00 08 00 00 00 00 10 46 18 40 00 00:00:00.017 READ DMA EXT 25 00 00 08 00 00 00 00 10 3e 18 40 00 00:00:00.017 READ DMA EXT Error 4233 [0] occurred at disk power-on lifetime: 8173 hours (340 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 06 48 ff 57 40 00 Error: UNC at LBA = 0x0648ff57 = 105447255 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 06 48 ff 57 40 00 00:00:04.468 READ FPDMA QUEUED 60 00 00 00 01 00 00 06 48 ff 57 40 00 00:00:04.534 READ FPDMA QUEUED 61 00 00 00 08 00 00 17 ac 06 90 40 00 00:00:04.534 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 83 36 70 40 00 00:00:04.534 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 84 09 a0 40 00 00:00:04.534 WRITE FPDMA QUEUED Error 4232 [7] occurred at disk power-on lifetime: 8173 hours (340 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 06 48 ff 57 40 00 Error: WP at LBA = 0x0648ff57 = 105447255 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 00 83 36 70 40 00 00:00:04.476 WRITE FPDMA QUEUED 60 00 00 00 01 00 00 06 48 ff 57 40 00 00:00:04.466 READ FPDMA QUEUED 60 00 00 00 01 00 00 06 48 ff 57 40 00 00:00:04.474 READ FPDMA QUEUED 61 00 00 00 10 00 00 18 7c 0d c0 40 00 00:00:04.474 WRITE FPDMA QUEUED 61 00 00 00 10 00 00 18 7e aa 50 40 00 00:00:04.474 WRITE FPDMA QUEUED Error 4231 [6] occurred at disk power-on lifetime: 8173 hours (340 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 06 48 ff 56 40 00 Error: UNC at LBA = 0x0648ff56 = 105447254 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 06 48 ff 56 40 00 00:00:04.463 READ FPDMA QUEUED 60 00 00 00 01 00 00 06 48 ff 56 40 00 00:00:04.471 READ FPDMA QUEUED 61 00 00 00 08 00 00 18 81 ac c0 40 00 00:00:04.471 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 18 81 26 60 40 00 00:00:04.471 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 22 5a 9c d8 40 00 00:00:04.471 WRITE FPDMA QUEUED Error 4230 [5] occurred at disk power-on lifetime: 8173 hours (340 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 06 48 ff 55 40 00 Error: UNC at LBA = 0x0648ff55 = 105447253 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 06 48 ff 55 40 00 00:00:04.463 READ FPDMA QUEUED 60 00 00 00 01 00 00 06 48 ff 55 40 00 00:00:04.469 READ FPDMA QUEUED 61 00 00 00 08 00 00 18 75 5b 70 40 00 00:00:04.469 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 18 75 5c 48 40 00 00:00:04.469 WRITE FPDMA QUEUED 60 00 00 00 08 00 00 18 97 c5 b0 40 00 00:00:04.469 READ FPDMA QUEUED Error 4229 [4] occurred at disk power-on lifetime: 8173 hours (340 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 06 48 ff 54 40 00 Error: UNC at LBA = 0x0648ff54 = 105447252 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 01 00 00 06 48 ff 54 40 00 00:00:04.463 READ FPDMA QUEUED 60 00 00 00 01 00 00 06 48 ff 54 40 00 00:00:04.466 READ FPDMA QUEUED 61 00 00 00 08 00 00 18 73 19 30 40 00 00:00:04.466 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 06 d0 b0 a0 40 00 00:00:04.466 WRITE FPDMA QUEUED 61 00 00 00 10 00 00 00 83 18 50 40 00 00:00:04.466 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 36/37 Celsius Lifetime Min/Max Temperature: 14/48 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (29) Index Estimated Time Temperature Celsius 30 2022-03-23 15:05 36 ***************** 31 2022-03-23 15:10 37 ****************** 32 2022-03-23 15:15 37 ****************** 33 2022-03-23 15:20 37 ****************** 34 2022-03-23 15:25 25 ****** 35 2022-03-23 15:30 28 ********* 36 2022-03-23 15:35 31 ************ 37 2022-03-23 15:40 33 ************** 38 2022-03-23 15:45 34 *************** 39 2022-03-23 15:50 25 ****** 40 2022-03-23 15:55 29 ********** 41 2022-03-23 16:00 31 ************ 42 2022-03-23 16:05 33 ************** 43 2022-03-23 16:10 35 **************** 44 2022-03-23 16:15 35 **************** 45 2022-03-23 16:20 36 ***************** 46 2022-03-23 16:25 37 ****************** 47 2022-03-23 16:30 38 ******************* 48 2022-03-23 16:35 38 ******************* 49 2022-03-23 16:40 39 ******************** 50 2022-03-23 16:45 39 ******************** 51 2022-03-23 16:50 39 ******************** 52 2022-03-23 16:55 40 ********************* ... ..( 7 skipped). .. ********************* 60 2022-03-23 17:35 40 ********************* 61 2022-03-23 17:40 31 ************ 62 2022-03-23 17:45 34 *************** 63 2022-03-23 17:50 35 **************** 64 2022-03-23 17:55 37 ****************** 65 2022-03-23 18:00 37 ****************** 66 2022-03-23 18:05 38 ******************* 67 2022-03-23 18:10 38 ******************* 68 2022-03-23 18:15 39 ******************** ... ..( 8 skipped). .. ******************** 77 2022-03-23 19:00 39 ******************** 78 2022-03-23 19:05 40 ********************* ... ..( 4 skipped). .. ********************* 83 2022-03-23 19:30 40 ********************* 84 2022-03-23 19:35 27 ******** 85 2022-03-23 19:40 30 *********** 86 2022-03-23 19:45 32 ************* 87 2022-03-23 19:50 34 *************** 88 2022-03-23 19:55 35 **************** 89 2022-03-23 20:00 36 ***************** 90 2022-03-23 20:05 36 ***************** 91 2022-03-23 20:10 37 ****************** 92 2022-03-23 20:15 37 ****************** 93 2022-03-23 20:20 37 ****************** 94 2022-03-23 20:25 38 ******************* ... ..( 3 skipped). .. ******************* 98 2022-03-23 20:45 38 ******************* 99 2022-03-23 20:50 39 ******************** ... ..( 6 skipped). .. ******************** 106 2022-03-23 21:25 39 ******************** 107 2022-03-23 21:30 24 ***** 108 2022-03-23 21:35 28 ********* 109 2022-03-23 21:40 30 *********** 110 2022-03-23 21:45 32 ************* 111 2022-03-23 21:50 34 *************** 112 2022-03-23 21:55 34 *************** 113 2022-03-23 22:00 35 **************** 114 2022-03-23 22:05 36 ***************** 115 2022-03-23 22:10 36 ***************** 116 2022-03-23 22:15 37 ****************** 117 2022-03-23 22:20 37 ****************** 118 2022-03-23 22:25 24 ***** 119 2022-03-23 22:30 27 ******** 120 2022-03-23 22:35 29 ********** 121 2022-03-23 22:40 31 ************ 122 2022-03-23 22:45 33 ************** 123 2022-03-23 22:50 24 ***** 124 2022-03-23 22:55 28 ********* 125 2022-03-23 23:00 30 *********** 126 2022-03-23 23:05 32 ************* 127 2022-03-23 23:10 33 ************** 0 2022-03-23 23:15 34 *************** 1 2022-03-23 23:20 34 *************** 2 2022-03-23 23:25 35 **************** 3 2022-03-23 23:30 35 **************** 4 2022-03-23 23:35 36 ***************** 5 2022-03-23 23:40 36 ***************** 6 2022-03-23 23:45 24 ***** 7 2022-03-23 23:50 28 ********* 8 2022-03-23 23:55 30 *********** 9 2022-03-24 00:00 32 ************* 10 2022-03-24 00:05 33 ************** 11 2022-03-24 00:10 34 *************** 12 2022-03-24 00:15 35 **************** 13 2022-03-24 00:20 35 **************** 14 2022-03-24 00:25 36 ***************** 15 2022-03-24 00:30 36 ***************** 16 2022-03-24 00:35 37 ****************** 17 2022-03-24 00:40 37 ****************** 18 2022-03-24 00:45 37 ****************** 19 2022-03-24 00:50 38 ******************* ... ..( 2 skipped). .. ******************* 22 2022-03-24 01:05 38 ******************* 23 2022-03-24 01:10 37 ****************** ... ..( 4 skipped). .. ****************** 28 2022-03-24 01:35 37 ****************** 29 2022-03-24 01:40 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific


Hardware for Linux and BSD

GitHub