/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi Travelstar 5K160 Device Model: Hitachi HTS541612J9SA00 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: SBDOC70P User Capacity: 120 034 123 776 bytes [120 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 1 Local Time is: Fri Apr 14 13:16:15 2017 +06 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 645) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 73) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 106 106 040 - 4532 3 Spin_Up_Time POS--- 234 234 033 - 1 4 Start_Stop_Count -O--C- 099 099 000 - 1685 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 122 122 040 - 39 9 Power_On_Hours -O--C- 095 095 000 - 2550 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 1511 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 197 193 Load_Cycle_Count -O--C- 099 099 000 - 10021 194 Temperature_Celsius -O---- 130 130 000 - 42 (Min/Max 17/53) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 253 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 3 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3 [2] occurred at disk power-on lifetime: 483 hours (20 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 15 d0 a8 04 e0 00 Error: IDNF 1 sectors at LBA = 0x15d0a804 = 365996036 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 20 20 00 01 00 00 15 d0 a8 04 e0 08 00:05:44.500 READ DMA EXT 25 20 20 00 01 00 00 00 00 00 00 e0 08 00:05:44.400 READ DMA EXT 25 20 20 00 01 00 00 07 d7 68 00 e0 08 00:05:44.400 READ DMA EXT 25 20 20 00 01 00 00 00 00 00 00 e0 08 00:05:44.400 READ DMA EXT 25 20 20 00 01 00 00 07 d7 68 04 e0 08 00:05:44.400 READ DMA EXT Error 2 [1] occurred at disk power-on lifetime: 483 hours (20 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 15 d0 a8 04 e0 00 Error: IDNF 1 sectors at LBA = 0x15d0a804 = 365996036 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 20 20 00 01 00 00 15 d0 a8 04 e0 08 00:02:53.300 READ DMA EXT 25 20 20 00 01 00 00 00 00 00 00 e0 08 00:02:53.300 READ DMA EXT 25 20 20 00 01 00 00 07 d7 68 00 e0 08 00:02:53.300 READ DMA EXT 25 20 20 00 01 00 00 00 00 00 00 e0 08 00:02:53.300 READ DMA EXT 25 20 20 00 01 00 00 07 d7 68 04 e0 08 00:02:53.300 READ DMA EXT Error 1 [0] occurred at disk power-on lifetime: 483 hours (20 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 15 d0 a8 04 e0 00 Error: IDNF 1 sectors at LBA = 0x15d0a804 = 365996036 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 20 20 00 01 00 00 15 d0 a8 04 e0 08 00:01:22.700 READ DMA EXT 25 20 20 00 01 00 00 00 00 00 00 e0 08 00:01:22.700 READ DMA EXT 25 20 20 00 01 00 00 07 d7 68 00 e0 08 00:01:22.700 READ DMA EXT 25 20 20 00 01 00 00 00 00 00 00 e0 08 00:01:22.700 READ DMA EXT 25 20 20 00 01 00 00 07 d7 68 04 e0 08 00:01:22.700 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS