/dev/sda === START OF INFORMATION SECTION === Model Family: SandForce Driven SSDs Device Model: KINGSTON SV300S37A60G Serial Number: -- LU WWN Device Id: 5 0026b7 ... Firmware Version: 505ABBF1 User Capacity: 60 022 480 896 bytes [60,0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jan 1 17:15:51 2018 +07 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Disabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 48) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0021) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 120 120 050 - 0/0 5 Retired_Block_Count PO--CK 100 100 003 - 0 9 Power_On_Hours_and_Msec -O--CK 084 084 000 - 14721h+03m+02.910s 12 Power_Cycle_Count -O--CK 097 097 000 - 3174 171 Program_Fail_Count -O--CK 000 000 000 - 0 172 Erase_Fail_Count -O--CK 000 000 000 - 0 174 Unexpect_Power_Loss_Ct ----CK 000 000 000 - 466 177 Wear_Range_Delta ------ 000 000 000 - 6 181 Program_Fail_Count -O--CK 000 000 000 - 0 182 Erase_Fail_Count -O--CK 000 000 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 Airflow_Temperature_Cel ------ 029 064 000 - 29 (Min/Max 17/64) 194 Temperature_Celsius -O---K 029 064 000 - 29 (Min/Max 17/64) 195 ECC_Uncorr_Error_Count --SRC- 100 100 000 - 0/0 196 Reallocated_Event_Count PO--CK 100 100 003 - 0 201 Unc_Soft_Read_Err_Rate --SRC- 100 100 000 - 0/0 204 Soft_ECC_Correct_Rate --SRC- 100 100 000 - 0/0 230 Life_Curve_Status PO--C- 100 100 000 - 100 231 SSD_Life_Left PO--C- 096 096 010 - 0 233 SandForce_Internal ------ 000 000 000 - 23018 234 SandForce_Internal -O--CK 000 000 000 - 10172 241 Lifetime_Writes_GiB -O--CK 000 000 000 - 10172 242 Lifetime_Reads_GiB -O--CK 000 000 000 - 7973 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 0 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x04 SL R/O 1 Device Statistics log 0x09 SL R/W 1 Selective self-test log 0x11 SL R/O 1 SATA Phy Event Counters log 0x80-0x9f SL R/W 16 Host vendor specific log 0xb7 SL VS 16 Device vendor specific log 0xe0 SL R/W 1 SCT Command/Status 0xe1 SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log not supported SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test Log not supported SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) SCT Support Level: 1 Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 29/29 Celsius Lifetime Min/Max Temperature: 17/64 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 10 (Unknown, should be 2) Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/120 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 18772 (156) Invalid Temperature History Size or Index SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb === START OF INFORMATION SECTION === Model Family: Hitachi Travelstar 5K500.B Device Model: Hitachi HTS545050B9A300 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: PB4OC64G User Capacity: 500 107 862 016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Jan 1 17:15:51 2018 +07 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 645) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 158) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 109 109 040 - 4376 3 Spin_Up_Time POS--- 158 158 033 - 1 4 Start_Stop_Count -O--C- 097 097 000 - 5032 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 120 120 040 - 32 9 Power_On_Hours -O--C- 053 053 000 - 20838 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 3896 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 92 193 Load_Cycle_Count -O--C- 070 070 000 - 307282 194 Temperature_Celsius -O---- 183 183 000 - 30 (Min/Max 16/51) 196 Reallocated_Event_Count -O--CK 100 100 000 - 25 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 76 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 76 [3] occurred at disk power-on lifetime: 18109 hours (754 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 25 43 e9 24 e5 00 Error: UNC 4 sectors at LBA = 0x2543e924 = 625207588 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 25 43 e9 20 e0 08 09:14:30.400 READ DMA EXT 25 00 00 00 08 00 00 25 43 e9 18 e0 08 09:14:30.400 READ DMA EXT 25 00 00 00 08 00 00 25 43 e9 10 e0 08 09:14:30.400 READ DMA EXT 25 00 00 00 08 00 00 25 43 e9 08 e0 08 09:14:30.400 READ DMA EXT 25 00 00 00 08 00 00 25 43 e9 00 e0 08 09:14:30.400 READ DMA EXT Error 75 [2] occurred at disk power-on lifetime: 18109 hours (754 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 07 00 00 25 43 99 f9 e5 00 Error: UNC 7 sectors at LBA = 0x254399f9 = 625187321 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 25 43 99 f8 e0 08 09:14:22.200 READ DMA EXT 25 00 00 00 08 00 00 25 43 99 f0 e0 08 09:14:22.200 READ DMA EXT 25 00 00 00 08 00 00 25 43 99 e8 e0 08 09:14:22.200 READ DMA EXT 25 00 00 00 08 00 00 25 43 99 e0 e0 08 09:14:22.200 READ DMA EXT 25 00 00 00 08 00 00 25 43 99 d8 e0 08 09:14:22.200 READ DMA EXT Error 74 [1] occurred at disk power-on lifetime: 18109 hours (754 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 07 00 00 25 43 99 f9 e5 00 Error: UNC 7 sectors at LBA = 0x254399f9 = 625187321 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 02 00 00 00 25 43 98 00 e0 08 09:14:18.500 READ DMA EXT 25 00 00 02 00 00 00 25 43 96 00 e0 08 09:14:18.500 READ DMA EXT 25 00 00 02 00 00 00 25 43 94 00 e0 08 09:14:18.500 READ DMA EXT 25 00 00 02 00 00 00 25 43 92 00 e0 08 09:14:18.500 READ DMA EXT 25 00 00 02 00 00 00 25 43 90 00 e0 08 09:14:18.400 READ DMA EXT Error 73 [0] occurred at disk power-on lifetime: 18072 hours (753 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 25 43 e9 24 e5 00 Error: UNC 4 sectors at LBA = 0x2543e924 = 625207588 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 25 43 e9 20 e0 08 04:38:09.500 READ DMA EXT 25 00 00 00 08 00 00 25 43 e9 18 e0 08 04:38:09.500 READ DMA EXT 25 00 00 00 08 00 00 25 43 e9 10 e0 08 04:38:09.500 READ DMA EXT 25 00 00 00 08 00 00 25 43 e9 08 e0 08 04:38:09.500 READ DMA EXT 25 00 00 00 08 00 00 25 43 e9 00 e0 08 04:38:09.500 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 19000 - # 2 Extended offline Completed: read failure 50% 18516 625187321 # 3 Extended offline Completed: read failure 50% 18423 625187321 # 4 Extended offline Completed: read failure 20% 18112 625187321 # 5 Extended offline Completed: read failure 50% 17842 616334776 # 6 Extended offline Completed: read failure 50% 17248 616334776 # 7 Extended offline Completed: read failure 50% 17063 616334776 # 8 Short offline Completed without error 00% 16475 - # 9 Extended offline Completed: read failure 50% 15810 616334776 #10 Extended offline Completed: read failure 50% 14988 616334776 #11 Extended offline Completed: read failure 50% 14922 616333423 #12 Extended offline Completed: read failure 90% 14865 121915506 #13 Extended offline Completed: read failure 50% 14763 616334776 #14 Extended offline Completed: read failure 50% 13843 616333423 #15 Extended offline Completed: read failure 90% 13352 579107 #16 Extended offline Completed: read failure 90% 13042 579107 #17 Extended offline Completed: read failure 90% 12980 579107 #18 Extended offline Completed without error 00% 11899 - 15 of 15 failed self-tests are outdated by newer successful extended offline self-test # 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 29/30 Celsius Lifetime Min/Max Temperature: 16/51 Celsius Lifetime Average Temperature: 33 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 478 (472) Index Estimated Time Temperature Celsius 473 2018-01-01 09:18 43 ************************ ... ..( 45 skipped). .. ************************ 41 2018-01-01 10:04 43 ************************ 42 2018-01-01 10:05 42 *********************** 43 2018-01-01 10:06 42 *********************** 44 2018-01-01 10:07 41 ********************** 45 2018-01-01 10:08 40 ********************* 46 2018-01-01 10:09 40 ********************* 47 2018-01-01 10:10 39 ******************** 48 2018-01-01 10:11 38 ******************* 49 2018-01-01 10:12 38 ******************* 50 2018-01-01 10:13 38 ******************* 51 2018-01-01 10:14 37 ****************** 52 2018-01-01 10:15 36 ***************** ... ..( 3 skipped). .. ***************** 56 2018-01-01 10:19 36 ***************** 57 2018-01-01 10:20 35 **************** ... ..( 3 skipped). .. **************** 61 2018-01-01 10:24 35 **************** 62 2018-01-01 10:25 34 *************** ... ..( 4 skipped). .. *************** 67 2018-01-01 10:30 34 *************** 68 2018-01-01 10:31 33 ************** ... ..( 45 skipped). .. ************** 114 2018-01-01 11:17 33 ************** 115 2018-01-01 11:18 34 *************** 116 2018-01-01 11:19 35 **************** 117 2018-01-01 11:20 35 **************** 118 2018-01-01 11:21 35 **************** 119 2018-01-01 11:22 34 *************** ... ..( 5 skipped). .. *************** 125 2018-01-01 11:28 34 *************** 126 2018-01-01 11:29 33 ************** 127 2018-01-01 11:30 34 *************** 128 2018-01-01 11:31 34 *************** 129 2018-01-01 11:32 35 **************** ... ..( 4 skipped). .. **************** 134 2018-01-01 11:37 35 **************** 135 2018-01-01 11:38 36 ***************** 136 2018-01-01 11:39 35 **************** 137 2018-01-01 11:40 35 **************** 138 2018-01-01 11:41 35 **************** 139 2018-01-01 11:42 34 *************** 140 2018-01-01 11:43 34 *************** 141 2018-01-01 11:44 34 *************** 142 2018-01-01 11:45 33 ************** ... ..( 3 skipped). .. ************** 146 2018-01-01 11:49 33 ************** 147 2018-01-01 11:50 32 ************* ... ..( 5 skipped). .. ************* 153 2018-01-01 11:56 32 ************* 154 2018-01-01 11:57 28 ********* ... ..( 2 skipped). .. ********* 157 2018-01-01 12:00 28 ********* 158 2018-01-01 12:01 29 ********** ... ..( 6 skipped). .. ********** 165 2018-01-01 12:08 29 ********** 166 2018-01-01 12:09 30 *********** ... ..( 24 skipped). .. *********** 191 2018-01-01 12:34 30 *********** 192 2018-01-01 12:35 31 ************ ... ..( 79 skipped). .. ************ 272 2018-01-01 13:55 31 ************ 273 2018-01-01 13:56 30 *********** 274 2018-01-01 13:57 31 ************ ... ..( 9 skipped). .. ************ 284 2018-01-01 14:07 31 ************ 285 2018-01-01 14:08 30 *********** ... ..( 26 skipped). .. *********** 312 2018-01-01 14:35 30 *********** 313 2018-01-01 14:36 25 ****** 314 2018-01-01 14:37 25 ****** 315 2018-01-01 14:38 25 ****** 316 2018-01-01 14:39 26 ******* 317 2018-01-01 14:40 26 ******* 318 2018-01-01 14:41 27 ******** 319 2018-01-01 14:42 27 ******** 320 2018-01-01 14:43 27 ******** 321 2018-01-01 14:44 28 ********* ... ..( 2 skipped). .. ********* 324 2018-01-01 14:47 28 ********* 325 2018-01-01 14:48 29 ********** ... ..( 5 skipped). .. ********** 331 2018-01-01 14:54 29 ********** 332 2018-01-01 14:55 30 *********** ... ..( 42 skipped). .. *********** 375 2018-01-01 15:38 30 *********** 376 2018-01-01 15:39 31 ************ ... ..( 15 skipped). .. ************ 392 2018-01-01 15:55 31 ************ 393 2018-01-01 15:56 30 *********** ... ..( 2 skipped). .. *********** 396 2018-01-01 15:59 30 *********** 397 2018-01-01 16:00 31 ************ 398 2018-01-01 16:01 31 ************ 399 2018-01-01 16:02 31 ************ 400 2018-01-01 16:03 30 *********** 401 2018-01-01 16:04 31 ************ 402 2018-01-01 16:05 30 *********** 403 2018-01-01 16:06 31 ************ ... ..( 35 skipped). .. ************ 439 2018-01-01 16:42 31 ************ 440 2018-01-01 16:43 30 *********** 441 2018-01-01 16:44 29 ********** ... ..( 2 skipped). .. ********** 444 2018-01-01 16:47 29 ********** 445 2018-01-01 16:48 30 *********** ... ..( 26 skipped). .. *********** 472 2018-01-01 17:15 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS