/dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.19-1-pve] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: MB2000EBZQC Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: HPG2 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7202 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Jul 14 04:53:08 2021 PKT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 617) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 316) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x103d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 082 055 044 - 184333637 3 Spin_Up_Time PO---- 093 091 070 - 0 4 Start_Stop_Count -O--CK 093 093 020 - 7273 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 2 7 Seek_Error_Rate POSR-- 075 060 030 - 32248879 9 Power_On_Hours -O--CK 095 095 000 - 4964 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 580 180 Unknown_HDD_Attribute PO-RCK 100 100 030 - 1500093548 184 End-to-End_Error -O--CK 100 100 003 - 0 187 Reported_Uncorrect -O--CK 006 006 000 - 94 188 Command_Timeout -O--CK 100 097 000 - 47245361478 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 058 038 045 Past 42 (Min/Max 36/44 #1817) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 097 097 000 - 7568 193 Load_Cycle_Count -O--CK 097 097 000 - 7769 194 Temperature_Celsius -O---K 042 062 000 - 42 (0 19 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 118 099 000 - 184333637 196 Reallocated_Event_Count PO--CK 100 100 036 - 2 197 Current_Pending_Sector -O--C- 099 094 000 - 58 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL,SL R/O 1 SATA NCQ Non-Data log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xb6 GPL VS 1918 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 598 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 598 [17] occurred at disk power-on lifetime: 1783 hours (74 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 36 38 31 a2 00 00 Error: UNC at LBA = 0x363831a2 = 909652386 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 00 00 00 00 40 00 3d+19:07:29.584 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:29.584 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:29.398 READ LOG EXT 60 00 00 01 00 00 00 00 00 00 00 40 00 3d+19:07:26.996 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:26.996 READ FPDMA QUEUED Error 597 [16] occurred at disk power-on lifetime: 1783 hours (74 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 36 38 31 a2 00 00 Error: UNC at LBA = 0x363831a2 = 909652386 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 00 00 00 00 40 00 3d+19:07:26.996 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:26.996 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:26.820 READ LOG EXT 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:24.476 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:24.400 READ LOG EXT Error 596 [15] occurred at disk power-on lifetime: 1783 hours (74 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 36 38 31 a2 00 00 Error: UNC at LBA = 0x363831a2 = 909652386 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:24.476 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:24.400 READ LOG EXT 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:22.077 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:21.894 READ LOG EXT 60 00 00 01 00 00 00 00 00 00 00 40 00 3d+19:07:19.455 READ FPDMA QUEUED Error 595 [14] occurred at disk power-on lifetime: 1783 hours (74 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 36 38 31 a2 00 00 Error: UNC at LBA = 0x363831a2 = 909652386 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:22.077 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:21.894 READ LOG EXT 60 00 00 01 00 00 00 00 00 00 00 40 00 3d+19:07:19.455 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:19.455 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:19.265 READ LOG EXT Error 594 [13] occurred at disk power-on lifetime: 1783 hours (74 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 36 38 31 a2 00 00 Error: UNC at LBA = 0x363831a2 = 909652386 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 00 00 00 00 40 00 3d+19:07:19.455 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:19.455 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:19.265 READ LOG EXT 60 00 00 01 00 00 00 00 00 00 00 40 00 3d+19:07:16.847 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:16.847 READ FPDMA QUEUED Error 593 [12] occurred at disk power-on lifetime: 1783 hours (74 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 36 38 31 a2 00 00 Error: UNC at LBA = 0x363831a2 = 909652386 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 00 00 00 00 40 00 3d+19:07:16.847 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:16.847 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:16.665 READ LOG EXT 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:14.331 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:14.150 READ LOG EXT Error 592 [11] occurred at disk power-on lifetime: 1783 hours (74 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 36 38 31 a2 00 00 Error: UNC at LBA = 0x363831a2 = 909652386 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:14.331 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:14.150 READ LOG EXT 60 00 00 01 00 00 00 00 00 00 00 40 00 3d+19:07:11.735 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:11.735 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:11.558 READ LOG EXT Error 591 [10] occurred at disk power-on lifetime: 1783 hours (74 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 36 38 31 a2 00 00 Error: UNC at LBA = 0x363831a2 = 909652386 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 00 00 00 00 40 00 3d+19:07:11.735 READ FPDMA QUEUED 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:11.735 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:11.558 READ LOG EXT 60 00 00 00 08 00 00 36 38 31 a0 40 00 3d+19:07:09.227 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 00 00 3d+19:07:08.766 READ LOG EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 4887 3737673 # 2 Extended offline Completed: read failure 90% 4887 3737673 # 3 Short offline Completed without error 00% 4887 - # 4 Extended offline Completed: read failure 90% 2385 14583175 # 5 Short offline Completed without error 00% 2369 - # 6 Short offline Completed without error 00% 1258 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: 36/44 Celsius Lifetime Min/Max Temperature: 19/62 Celsius Specified Max Operating Temperature: 60 Celsius Under/Over Temperature Limit Count: 0/40 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (32) Index Estimated Time Temperature Celsius 33 2021-07-13 07:40 43 ************************ ... ..( 27 skipped). .. ************************ 61 2021-07-13 12:20 43 ************************ 62 2021-07-13 12:30 ? - 63 2021-07-13 12:40 43 ************************ 64 2021-07-13 12:50 ? - 65 2021-07-13 13:00 43 ************************ 66 2021-07-13 13:10 ? - 67 2021-07-13 13:20 42 *********************** 68 2021-07-13 13:30 ? - 69 2021-07-13 13:40 42 *********************** 70 2021-07-13 13:50 ? - 71 2021-07-13 14:00 41 ********************** 72 2021-07-13 14:10 ? - 73 2021-07-13 14:20 40 ********************* 74 2021-07-13 14:30 ? - 75 2021-07-13 14:40 37 ****************** 76 2021-07-13 14:50 ? - 77 2021-07-13 15:00 35 **************** 78 2021-07-13 15:10 ? - 79 2021-07-13 15:20 35 **************** 80 2021-07-13 15:30 ? - 81 2021-07-13 15:40 35 **************** 82 2021-07-13 15:50 35 **************** 83 2021-07-13 16:00 38 ******************* 84 2021-07-13 16:10 40 ********************* 85 2021-07-13 16:20 41 ********************** 86 2021-07-13 16:30 ? - 87 2021-07-13 16:40 42 *********************** ... ..( 2 skipped). .. *********************** 90 2021-07-13 17:10 42 *********************** 91 2021-07-13 17:20 43 ************************ ... ..( 13 skipped). .. ************************ 105 2021-07-13 19:40 43 ************************ 106 2021-07-13 19:50 42 *********************** ... ..( 10 skipped). .. *********************** 117 2021-07-13 21:40 42 *********************** 118 2021-07-13 21:50 ? - 119 2021-07-13 22:00 36 ***************** 120 2021-07-13 22:10 ? - 121 2021-07-13 22:20 36 ***************** 122 2021-07-13 22:30 36 ***************** 123 2021-07-13 22:40 39 ******************** 124 2021-07-13 22:50 41 ********************** 125 2021-07-13 23:00 42 *********************** 126 2021-07-13 23:10 43 ************************ 127 2021-07-13 23:20 43 ************************ 0 2021-07-13 23:30 44 ************************* ... ..( 22 skipped). .. ************************* 23 2021-07-14 03:20 44 ************************* 24 2021-07-14 03:30 43 ************************ ... ..( 7 skipped). .. ************************ 32 2021-07-14 04:50 43 ************************ SCT Error Recovery Control: Read: 100 (10.0 seconds) Write: 100 (10.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 580 --- Lifetime Power-On Resets 0x01 0x010 4 4964 --- Power-on Hours 0x01 0x018 6 10402001637 --- Logical Sectors Written 0x01 0x020 6 112964076 --- Number of Write Commands 0x01 0x028 6 20171684163 --- Logical Sectors Read 0x01 0x030 6 146308102 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 2497670506 N-- Spindle Motor Power-on Hours 0x03 0x010 4 2497670506 N-- Head Flying Hours 0x03 0x018 4 7769 --- Head Load Events 0x03 0x020 4 2 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 30 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 596 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 326 --- Resets Between Cmd Acceptance and Completion |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdd smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.19-1-pve] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: MB2000GCWDA Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: HPGD User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jul 14 04:53:09 2021 PKT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 592) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 249) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SCT capabilities: (0x103d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 075 063 044 - 30888793 3 Spin_Up_Time PO---- 096 095 070 - 0 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 095 060 030 - 3249354172 9 Power_On_Hours -O--CK 041 041 000 - 52014 10 Spin_Retry_Count PO--C- 100 100 097 - 0 180 Unknown_HDD_Attribute PO-RCK 100 085 030 - 1207865065 194 Temperature_Celsius -O---K 045 059 000 - 45 (0 19 0 0 0) 196 Reallocated_Event_Count PO--CK 100 100 010 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL,SL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xb5 SL VS 1 Device vendor specific log 0xb6 GPL VS 1918 Device vendor specific log 0xbd GPL VS 512 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc2 GPL,SL VS 50 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xd0 GPL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 00% 49588 - # 2 Extended offline Interrupted (host reset) 00% 49579 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 45 Celsius Power Cycle Min/Max Temperature: 38/50 Celsius Lifetime Min/Max Temperature: 19/59 Celsius Specified Max Operating Temperature: 60 Celsius Under/Over Temperature Limit Count: 0/39 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (115) Index Estimated Time Temperature Celsius 116 2021-07-13 07:40 42 *********************** ... ..( 3 skipped). .. *********************** 120 2021-07-13 08:20 42 *********************** 121 2021-07-13 08:30 43 ************************ ... ..( 28 skipped). .. ************************ 22 2021-07-13 13:20 43 ************************ 23 2021-07-13 13:30 44 ************************* ... ..( 7 skipped). .. ************************* 31 2021-07-13 14:50 44 ************************* 32 2021-07-13 15:00 43 ************************ ... ..( 14 skipped). .. ************************ 47 2021-07-13 17:30 43 ************************ 48 2021-07-13 17:40 44 ************************* 49 2021-07-13 17:50 44 ************************* 50 2021-07-13 18:00 44 ************************* 51 2021-07-13 18:10 43 ************************ ... ..( 21 skipped). .. ************************ 73 2021-07-13 21:50 43 ************************ 74 2021-07-13 22:00 ? - 75 2021-07-13 22:10 37 ****************** 76 2021-07-13 22:20 ? - 77 2021-07-13 22:30 38 ******************* 78 2021-07-13 22:40 40 ********************* 79 2021-07-13 22:50 44 ************************* 80 2021-07-13 23:00 46 *************************** 81 2021-07-13 23:10 47 **************************** 82 2021-07-13 23:20 48 ***************************** 83 2021-07-13 23:30 49 ****************************** 84 2021-07-13 23:40 49 ****************************** 85 2021-07-13 23:50 50 ******************************* ... ..( 11 skipped). .. ******************************* 97 2021-07-14 01:50 50 ******************************* 98 2021-07-14 02:00 49 ****************************** ... ..( 5 skipped). .. ****************************** 104 2021-07-14 03:00 49 ****************************** 105 2021-07-14 03:10 48 ***************************** 106 2021-07-14 03:20 47 **************************** 107 2021-07-14 03:30 47 **************************** 108 2021-07-14 03:40 46 *************************** ... ..( 6 skipped). .. *************************** 115 2021-07-14 04:50 46 *************************** SCT Error Recovery Control: Read: 100 (10.0 seconds) Write: 100 (10.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 44729 --- Lifetime Power-On Resets 0x01 0x010 4 52014 --- Power-on Hours 0x01 0x018 6 407640833222 --- Logical Sectors Written 0x01 0x020 6 1426453387 --- Number of Write Commands 0x01 0x028 6 995033366168 --- Logical Sectors Read 0x01 0x030 6 2870022399 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 2257 --- Spindle Motor Power-on Hours 0x03 0x010 4 2257 --- Head Flying Hours 0x03 0x018 4 46913 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 135 --- Resets Between Cmd Acceptance and Completion |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sde smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.19-1-pve] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Hajaan 256G Serial Number: -- Firmware Version: S0414 User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jul 14 04:53:09 2021 PKT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0 9 Power_On_Hours -O--CK 100 100 050 - 10187 12 Power_Cycle_Count -O--CK 100 100 050 - 736 160 Unknown_Attribute -O--CK 100 100 050 - 0 161 Unknown_Attribute PO--CK 100 100 050 - 100 163 Unknown_Attribute -O--CK 100 100 050 - 10 164 Unknown_Attribute -O--CK 100 100 050 - 880418 165 Unknown_Attribute -O--CK 100 100 050 - 9133 166 Unknown_Attribute -O--CK 100 100 050 - 357 167 Unknown_Attribute -O--CK 100 100 050 - 1216 168 Unknown_Attribute -O--CK 100 100 050 - 1500 169 Unknown_Attribute -O--CK 100 100 050 - 19 175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 0 177 Wear_Leveling_Count -O--CK 100 100 050 - 0 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0 192 Power-Off_Retract_Count -O--CK 100 100 050 - 705 194 Temperature_Celsius -O---K 100 100 050 - 36 195 Hardware_ECC_Recovered -O--CK 100 100 050 - 1675330 196 Reallocated_Event_Count -O--CK 100 100 050 - 0 197 Current_Pending_Sector -O--CK 100 100 050 - 0 198 Offline_Uncorrectable -O--CK 100 100 050 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 0 232 Available_Reservd_Space -O--CK 100 100 050 - 100 241 Total_LBAs_Written ----CK 100 100 050 - 1736344 242 Total_LBAs_Read ----CK 100 100 050 - 806283 245 Unknown_Attribute -O--CK 100 100 050 - 3623628 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xde GPL VS 8 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 299 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 299 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d1 01 01 00 00 4f 00 c2 01 00 00 00:00:00.000 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] 2f 00 00 01 01 00 00 00 00 00 03 00 00 00:00:00.000 READ LOG EXT 2f 00 00 01 01 00 00 00 00 00 00 00 00 00:00:00.000 READ LOG EXT b0 00 d5 01 01 00 00 4f 00 c2 00 00 00 00:00:00.000 SMART READ LOG b0 00 da 00 00 00 00 4f 00 c2 00 00 00 00:00:00.000 SMART RETURN STATUS Error 298 [1] log entry is empty Error 297 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d1 01 01 00 00 4f 00 c2 01 00 00 00:00:00.000 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] 2f 00 00 01 01 00 00 00 00 00 03 00 00 00:00:00.000 READ LOG EXT 2f 00 00 01 01 00 00 00 00 00 00 00 00 00:00:00.000 READ LOG EXT b0 00 d5 01 01 00 00 4f 00 c2 00 00 00 00:00:00.000 SMART READ LOG b0 00 da 00 00 00 00 4f 00 c2 00 00 00 00:00:00.000 SMART RETURN STATUS Error 296 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 00 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d5 01 01 00 00 4f 00 c2 00 00 08 00:00:00.000 SMART READ LOG 2f 00 00 01 01 00 00 00 00 00 03 00 08 00:00:00.000 READ LOG EXT ca 00 00 88 88 00 00 ce 00 f5 20 e2 08 00:00:00.000 WRITE DMA 2f 00 00 01 01 00 00 00 00 00 00 00 08 00:00:00.000 READ LOG EXT 35 00 00 78 78 00 02 cb 00 f5 a8 e0 08 00:00:00.000 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 736 --- Lifetime Power-On Resets 0x01 0x010 4 10187 --- Power-on Hours 0x01 0x018 6 2123928817 --- Logical Sectors Written 0x01 0x020 6 562158420 --- Number of Write Commands 0x01 0x028 6 1301012921 --- Logical Sectors Read 0x01 0x030 6 1068017253 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 81 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET /dev/sdf smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.19-1-pve] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: Lexar 256GB SSD Serial Number: -- LU WWN Device Id: 5 000000 ... Firmware Version: H190117D User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jul 14 04:53:10 2021 PKT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 33) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 4697 12 Power_Cycle_Count -O--C- 100 100 000 - 490 167 Unknown_Attribute -O---K 100 100 000 - 0 168 Unknown_Attribute -O--C- 100 100 000 - 2087 169 Unknown_Attribute PO--C- 096 096 010 - 8388624 171 Unknown_Attribute -O--CK 000 000 000 - 0 172 Unknown_Attribute -O--CK 000 000 000 - 0 173 Unknown_Attribute -O--C- 200 200 000 - 373673492621 175 Program_Fail_Count_Chip -O---K 100 100 010 - 0 177 Wear_Leveling_Count -O--C- 100 100 000 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--CK 100 100 000 - 3272 187 Reported_Uncorrect -O--CK 100 000 000 - 0 192 Power-Off_Retract_Count -O--C- 100 100 000 - 425 194 Temperature_Celsius -O---K 048 048 000 - 48 (Min/Max 48/48) 199 UDMA_CRC_Error_Count -O--C- 100 100 000 - 0 206 Unknown_SSD_Attribute -O--CK 200 200 000 - 87 207 Unknown_SSD_Attribute -O--CK 200 200 000 - 173 208 Unknown_SSD_Attribute -O--CK 200 200 000 - 141 209 Unknown_SSD_Attribute -O--CK 200 200 000 - 483 210 Unknown_Attribute -O--CK 200 200 000 - 614 211 Unknown_Attribute -O--CK 200 200 000 - 546 231 Unknown_SSD_Attribute PO---K 091 091 005 - 9 241 Total_LBAs_Written -O--CK 100 100 000 - 10166 242 Total_LBAs_Read -O--CK 100 100 000 - 5464 245 Unknown_Attribute -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 2087 (device log contains only the most recent 256 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2087 [38] occurred at disk power-on lifetime: 4413 hours (183 days + 21 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 00 00 00 01 0e 43 a8 40 80 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 01 00 00 00 00 00 00 00 80 02:45:15.800 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 02:45:15.800 SMART ENABLE OPERATIONS ef 00 02 00 00 00 00 00 00 00 00 00 80 02:45:15.800 SET FEATURES [Enable write cache] e1 00 00 00 00 00 00 00 00 00 00 00 80 02:45:15.800 IDLE IMMEDIATE ec 00 00 00 01 00 00 00 00 00 00 00 80 02:45:15.800 IDENTIFY DEVICE Error 2086 [37] occurred at disk power-on lifetime: 4413 hours (183 days + 21 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 79 00 00 00 07 24 88 40 00 Error: ICRC, ABRT 377 sectors at LBA = 0x00072488 = 468104 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 01 79 00 00 00 07 24 88 40 80 02:45:11.900 WRITE DMA EXT ec 00 00 00 01 00 00 00 00 00 00 00 80 02:45:11.800 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 02:45:11.800 SMART ENABLE OPERATIONS ef 00 02 00 00 00 00 00 00 00 00 00 80 02:45:11.800 SET FEATURES [Enable write cache] e1 00 00 00 00 00 00 00 00 00 00 00 80 02:45:11.800 IDLE IMMEDIATE Error 2085 [36] occurred at disk power-on lifetime: 4412 hours (183 days + 20 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 10 00 00 00 07 24 88 40 80 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 00 01 00 00 00 00 00 00 00 80 02:40:05.800 IDENTIFY DEVICE b0 00 d8 00 00 00 00 00 c2 4f 00 00 80 02:40:05.800 SMART ENABLE OPERATIONS ef 00 02 00 00 00 00 00 00 00 00 00 80 02:40:05.800 SET FEATURES [Enable write cache] e1 00 00 00 00 00 00 00 00 00 00 00 80 02:40:05.800 IDLE IMMEDIATE ec 00 00 00 01 00 00 00 00 00 00 00 80 02:40:05.800 IDENTIFY DEVICE Error 2084 [35] occurred at disk power-on lifetime: 1413 hours (58 days + 21 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 10 00 00 1d cf 31 b8 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.700 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.600 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.600 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.500 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.400 READ LOG EXT Error 2083 [34] occurred at disk power-on lifetime: 1413 hours (58 days + 21 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 08 00 00 1d cf 2f d8 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.600 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.600 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.500 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.400 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.400 READ LOG EXT Error 2082 [33] occurred at disk power-on lifetime: 1413 hours (58 days + 21 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 18 00 00 1d cf 2f 00 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.600 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.500 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.400 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.400 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.300 READ LOG EXT Error 2081 [32] occurred at disk power-on lifetime: 1413 hours (58 days + 21 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 00 00 00 00 00 02 08 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.300 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.200 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.200 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.100 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:01.000 READ LOG EXT Error 2080 [31] occurred at disk power-on lifetime: 1413 hours (58 days + 21 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 08 00 00 00 00 00 28 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:00.900 READ LOG EXT ec 00 00 00 00 00 00 00 00 00 00 00 80 00:37:00.800 IDENTIFY DEVICE 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:00.800 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:00.700 READ LOG EXT 2f 00 00 00 01 00 00 00 00 00 10 00 80 00:37:00.700 READ LOG EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 1650 - # 2 Short offline Completed without error 00% 652 - # 3 Short offline Completed without error 00% 169 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 48 Celsius Power Cycle Min/Max Temperature: ?/48 Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -127/127 Celsius Min/Max Temperature Limit: -127/127 Celsius Temperature History Size (Index): 478 (445) Index Estimated Time Temperature Celsius 446 2021-07-13 20:56 48 ***************************** ... ..(236 skipped). .. ***************************** 205 2021-07-14 00:53 48 ***************************** 206 2021-07-14 00:54 ? - 207 2021-07-14 00:55 48 ***************************** ... ..( 3 skipped). .. ***************************** 211 2021-07-14 00:59 48 ***************************** 212 2021-07-14 01:00 ? - 213 2021-07-14 01:01 48 ***************************** 214 2021-07-14 01:02 ? - ... ..( 3 skipped). .. - 218 2021-07-14 01:06 ? - 219 2021-07-14 01:07 48 ***************************** ... ..( 40 skipped). .. ***************************** 260 2021-07-14 01:48 48 ***************************** 261 2021-07-14 01:49 ? - 262 2021-07-14 01:50 ? - 263 2021-07-14 01:51 ? - 264 2021-07-14 01:52 48 ***************************** 265 2021-07-14 01:53 ? - ... ..( 2 skipped). .. - 268 2021-07-14 01:56 ? - 269 2021-07-14 01:57 48 ***************************** 270 2021-07-14 01:58 ? - 271 2021-07-14 01:59 ? - 272 2021-07-14 02:00 48 ***************************** 273 2021-07-14 02:01 48 ***************************** 274 2021-07-14 02:02 ? - 275 2021-07-14 02:03 48 ***************************** 276 2021-07-14 02:04 48 ***************************** 277 2021-07-14 02:05 ? - ... ..( 3 skipped). .. - 281 2021-07-14 02:09 ? - 282 2021-07-14 02:10 48 ***************************** ... ..( 2 skipped). .. ***************************** 285 2021-07-14 02:13 48 ***************************** 286 2021-07-14 02:14 ? - 287 2021-07-14 02:15 48 ***************************** 288 2021-07-14 02:16 48 ***************************** 289 2021-07-14 02:17 ? - 290 2021-07-14 02:18 48 ***************************** ... ..( 8 skipped). .. ***************************** 299 2021-07-14 02:27 48 ***************************** 300 2021-07-14 02:28 ? - 301 2021-07-14 02:29 48 ***************************** ... ..( 8 skipped). .. ***************************** 310 2021-07-14 02:38 48 ***************************** 311 2021-07-14 02:39 ? - 312 2021-07-14 02:40 48 ***************************** 313 2021-07-14 02:41 ? - 314 2021-07-14 02:42 48 ***************************** ... ..( 3 skipped). .. ***************************** 318 2021-07-14 02:46 48 ***************************** 319 2021-07-14 02:47 ? - 320 2021-07-14 02:48 48 ***************************** ... ..( 77 skipped). .. ***************************** 398 2021-07-14 04:06 48 ***************************** 399 2021-07-14 04:07 ? - 400 2021-07-14 04:08 48 ***************************** ... ..( 5 skipped). .. ***************************** 406 2021-07-14 04:14 48 ***************************** 407 2021-07-14 04:15 ? - 408 2021-07-14 04:16 ? - 409 2021-07-14 04:17 48 ***************************** 410 2021-07-14 04:18 48 ***************************** 411 2021-07-14 04:19 ? - 412 2021-07-14 04:20 48 ***************************** 413 2021-07-14 04:21 48 ***************************** 414 2021-07-14 04:22 48 ***************************** 415 2021-07-14 04:23 ? - 416 2021-07-14 04:24 ? - 417 2021-07-14 04:25 48 ***************************** 418 2021-07-14 04:26 ? - ... ..( 3 skipped). .. - 422 2021-07-14 04:30 ? - 423 2021-07-14 04:31 48 ***************************** 424 2021-07-14 04:32 ? - ... ..( 6 skipped). .. - 431 2021-07-14 04:39 ? - 432 2021-07-14 04:40 48 ***************************** ... ..( 12 skipped). .. ***************************** 445 2021-07-14 04:53 48 ***************************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 490 --- Lifetime Power-On Resets 0x01 0x010 4 4697 --- Power-on Hours 0x01 0x018 6 21320461526 --- Logical Sectors Written 0x01 0x020 6 374184200 --- Number of Write Commands 0x01 0x028 6 11459446130 --- Logical Sectors Read 0x01 0x030 6 226418779 --- Number of Read Commands 0x01 0x038 6 4324740544288 --- Date and Time TimeStamp 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 23 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 39 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC