/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.74-generic-2rosa2021.1-x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Laptop HDD Device Model: ST500LT012-1DG142 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 1003YAM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Feb 23 00:31:16 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 99) minutes. SCT capabilities: (0x103d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 119 089 006 - 207482560 3 Spin_Up_Time PO---K 099 098 000 - 0 4 Start_Stop_Count -O--CK 093 093 000 - 8118 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-K 079 060 030 - 13123849289 9 Power_On_Hours -O--CK 095 095 000 - 4861 10 Spin_Retry_Count PO--CK 100 100 097 - 0 12 Power_Cycle_Count -O--CK 093 093 000 - 8107 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 878 188 Command_Timeout -O--CK 100 100 000 - 4295032833 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 073 055 045 - 27 (Min/Max 19/30) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 110 192 Power-Off_Retract_Count -O---K 100 100 000 - 7 193 Load_Cycle_Count -O--CK 072 072 000 - 56644 194 Temperature_Celsius -O---K 027 045 000 - 27 (0 10 0 0 0) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xb6 GPL VS 16385 Device vendor specific log 0xbd-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xc4 GPL,SL VS 18 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 906 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 906 [5] occurred at disk power-on lifetime: 4553 hours (189 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 70 93 7b 00 00 Error: UNC at LBA = 0x0070937b = 7377787 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 da d8 00 04 00 00 00 70 93 7b e0 00 00:04:59.585 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:59.585 READ DMA EXT 42 da d8 00 04 00 00 00 70 93 77 e0 00 00:04:57.137 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:57.136 READ DMA EXT 42 da d8 00 08 00 00 00 70 93 87 e0 00 00:04:57.133 READ VERIFY SECTOR(S) EXT Error 905 [4] occurred at disk power-on lifetime: 4553 hours (189 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 70 93 78 00 00 Error: UNC at LBA = 0x00709378 = 7377784 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 da d8 00 04 00 00 00 70 93 77 e0 00 00:04:57.137 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:57.136 READ DMA EXT 42 da d8 00 08 00 00 00 70 93 87 e0 00 00:04:57.133 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:57.133 READ DMA EXT 42 da d8 00 08 00 00 00 70 93 7f e0 00 00:04:54.592 READ VERIFY SECTOR(S) EXT Error 904 [3] occurred at disk power-on lifetime: 4553 hours (189 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 70 93 7f 00 00 Error: UNC at LBA = 0x0070937f = 7377791 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 da d8 00 08 00 00 00 70 93 7f e0 00 00:04:54.592 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:54.592 READ DMA EXT 42 da d8 00 08 00 00 00 70 93 77 e0 00 00:04:52.167 READ VERIFY SECTOR(S) EXT 42 da d8 00 08 00 00 00 70 93 6f e0 00 00:04:52.155 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:52.154 READ DMA EXT Error 903 [2] occurred at disk power-on lifetime: 4553 hours (189 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 70 93 78 00 00 Error: UNC at LBA = 0x00709378 = 7377784 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 da d8 00 08 00 00 00 70 93 77 e0 00 00:04:52.167 READ VERIFY SECTOR(S) EXT 42 da d8 00 08 00 00 00 70 93 6f e0 00 00:04:52.155 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:52.154 READ DMA EXT 42 da d8 00 10 00 00 00 70 93 8f e0 00 00:04:52.151 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:52.151 READ DMA EXT Error 902 [1] occurred at disk power-on lifetime: 4553 hours (189 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 70 93 7f 00 00 Error: UNC at LBA = 0x0070937f = 7377791 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 da d8 00 10 00 00 00 70 93 7f e0 00 00:04:49.588 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:49.588 READ DMA EXT 42 da d8 00 10 00 00 00 70 93 6f e0 00 00:04:47.152 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:47.151 READ DMA EXT 42 da d8 00 10 00 00 00 70 93 5f e0 00 00:04:47.140 READ VERIFY SECTOR(S) EXT Error 901 [0] occurred at disk power-on lifetime: 4553 hours (189 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 70 93 78 00 00 Error: UNC at LBA = 0x00709378 = 7377784 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 da d8 00 10 00 00 00 70 93 6f e0 00 00:04:47.152 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:47.151 READ DMA EXT 42 da d8 00 10 00 00 00 70 93 5f e0 00 00:04:47.140 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:47.139 READ DMA EXT 42 da d8 00 20 00 00 00 70 93 9f e0 00 00:04:47.136 READ VERIFY SECTOR(S) EXT Error 900 [19] occurred at disk power-on lifetime: 4553 hours (189 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 70 93 7f 00 00 Error: UNC at LBA = 0x0070937f = 7377791 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 da d8 00 20 00 00 00 70 93 7f e0 00 00:04:44.595 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:44.595 READ DMA EXT 42 da d8 00 20 00 00 00 70 93 5f e0 00 00:04:42.159 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:42.158 READ DMA EXT 42 da d8 00 20 00 00 00 70 93 3f e0 00 00:04:42.154 READ VERIFY SECTOR(S) EXT Error 899 [18] occurred at disk power-on lifetime: 4553 hours (189 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 70 93 78 00 00 Error: UNC at LBA = 0x00709378 = 7377784 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 da d8 00 20 00 00 00 70 93 5f e0 00 00:04:42.159 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:42.158 READ DMA EXT 42 da d8 00 20 00 00 00 70 93 3f e0 00 00:04:42.154 READ VERIFY SECTOR(S) EXT 25 da d8 00 01 00 00 00 00 00 00 e0 00 00:04:42.154 READ DMA EXT 42 da d8 00 40 00 00 00 70 93 7f e0 00 00:04:39.636 READ VERIFY SECTOR(S) EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 60% 4 - # 2 Short offline Completed without error 00% 4 - # 3 Short offline Completed without error 00% 3 - # 4 Short offline Completed without error 00% 3 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 19/30 Celsius Lifetime Min/Max Temperature: 10/45 Celsius Under/Over Temperature Limit Count: 0/6 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 30 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (10) Index Estimated Time Temperature Celsius 11 2024-02-20 09:00 27 ******** ... ..( 2 skipped). .. ******** 14 2024-02-20 10:30 27 ******** 15 2024-02-20 11:00 28 ********* 16 2024-02-20 11:30 29 ********** 17 2024-02-20 12:00 27 ******** 18 2024-02-20 12:30 26 ******* 19 2024-02-20 13:00 27 ******** 20 2024-02-20 13:30 28 ********* 21 2024-02-20 14:00 29 ********** ... ..( 3 skipped). .. ********** 25 2024-02-20 16:00 29 ********** 26 2024-02-20 16:30 ? - 27 2024-02-20 17:00 21 ** 28 2024-02-20 17:30 28 ********* 29 2024-02-20 18:00 ? - 30 2024-02-20 18:30 28 ********* 31 2024-02-20 19:00 27 ******** ... ..( 3 skipped). .. ******** 35 2024-02-20 21:00 27 ******** 36 2024-02-20 21:30 28 ********* 37 2024-02-20 22:00 ? - 38 2024-02-20 22:30 29 ********** 39 2024-02-20 23:00 ? - 40 2024-02-20 23:30 26 ******* 41 2024-02-21 00:00 ? - 42 2024-02-21 00:30 20 * 43 2024-02-21 01:00 25 ****** 44 2024-02-21 01:30 25 ****** 45 2024-02-21 02:00 25 ****** 46 2024-02-21 02:30 26 ******* 47 2024-02-21 03:00 26 ******* 48 2024-02-21 03:30 25 ****** 49 2024-02-21 04:00 25 ****** 50 2024-02-21 04:30 25 ****** 51 2024-02-21 05:00 26 ******* 52 2024-02-21 05:30 26 ******* 53 2024-02-21 06:00 26 ******* 54 2024-02-21 06:30 30 *********** 55 2024-02-21 07:00 ? - 56 2024-02-21 07:30 20 * 57 2024-02-21 08:00 ? - 58 2024-02-21 08:30 21 ** 59 2024-02-21 09:00 26 ******* 60 2024-02-21 09:30 26 ******* 61 2024-02-21 10:00 26 ******* 62 2024-02-21 10:30 28 ********* 63 2024-02-21 11:00 28 ********* 64 2024-02-21 11:30 28 ********* 65 2024-02-21 12:00 ? - 66 2024-02-21 12:30 18 - 67 2024-02-21 13:00 25 ****** 68 2024-02-21 13:30 27 ******** 69 2024-02-21 14:00 27 ******** 70 2024-02-21 14:30 27 ******** 71 2024-02-21 15:00 26 ******* 72 2024-02-21 15:30 28 ********* 73 2024-02-21 16:00 29 ********** 74 2024-02-21 16:30 30 *********** ... ..( 3 skipped). .. *********** 78 2024-02-21 18:30 30 *********** 79 2024-02-21 19:00 29 ********** 80 2024-02-21 19:30 32 ************* 81 2024-02-21 20:00 30 *********** 82 2024-02-21 20:30 30 *********** 83 2024-02-21 21:00 ? - 84 2024-02-21 21:30 20 * 85 2024-02-21 22:00 27 ******** 86 2024-02-21 22:30 27 ******** 87 2024-02-21 23:00 27 ******** 88 2024-02-21 23:30 25 ****** ... ..( 3 skipped). .. ****** 92 2024-02-22 01:30 25 ****** 93 2024-02-22 02:00 27 ******** 94 2024-02-22 02:30 27 ******** 95 2024-02-22 03:00 ? - 96 2024-02-22 03:30 22 *** 97 2024-02-22 04:00 28 ********* 98 2024-02-22 04:30 27 ******** 99 2024-02-22 05:00 28 ********* 100 2024-02-22 05:30 28 ********* 101 2024-02-22 06:00 ? - 102 2024-02-22 06:30 20 * 103 2024-02-22 07:00 ? - 104 2024-02-22 07:30 22 *** 105 2024-02-22 08:00 28 ********* 106 2024-02-22 08:30 29 ********** 107 2024-02-22 09:00 30 *********** 108 2024-02-22 09:30 30 *********** 109 2024-02-22 10:00 30 *********** 110 2024-02-22 10:30 31 ************ 111 2024-02-22 11:00 30 *********** 112 2024-02-22 11:30 30 *********** 113 2024-02-22 12:00 30 *********** 114 2024-02-22 12:30 32 ************* 115 2024-02-22 13:00 32 ************* 116 2024-02-22 13:30 32 ************* 117 2024-02-22 14:00 31 ************ 118 2024-02-22 14:30 31 ************ 119 2024-02-22 15:00 29 ********** 120 2024-02-22 15:30 27 ******** 121 2024-02-22 16:00 27 ******** 122 2024-02-22 16:30 29 ********** 123 2024-02-22 17:00 30 *********** 124 2024-02-22 17:30 32 ************* 125 2024-02-22 18:00 28 ********* 126 2024-02-22 18:30 27 ******** 127 2024-02-22 19:00 27 ******** 0 2024-02-22 19:30 28 ********* 1 2024-02-22 20:00 29 ********** 2 2024-02-22 20:30 30 *********** 3 2024-02-22 21:00 31 ************ 4 2024-02-22 21:30 ? - 5 2024-02-22 22:00 19 - 6 2024-02-22 22:30 24 ***** 7 2024-02-22 23:00 27 ******** 8 2024-02-22 23:30 28 ********* 9 2024-02-23 00:00 28 ********* 10 2024-02-23 00:30 27 ******** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS