/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue EIDE Device Model: WDC WD5000AAKB-00H8A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 05.04E05 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) Transport Type: Parallel, ATA8-APT Local Time is: Fri Jan 18 00:28:59 2019 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 100) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 199 199 051 - 14980 3 Spin_Up_Time POS--K 162 159 021 - 4883 4 Start_Stop_Count -O--CK 097 097 000 - 3086 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 090 090 000 - 7594 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2860 192 Power-Off_Retract_Count -O--CK 199 199 000 - 856 193 Load_Cycle_Count -O--CK 199 199 000 - 3086 194 Temperature_Celsius -O---K 103 097 000 - 44 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 21 198 Offline_Uncorrectable ----CK 200 200 000 - 6 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 1 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 29680 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 29680 [15] occurred at disk power-on lifetime: 7562 hours (315 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 2a 00 1b d2 e0 00 Error: UNC 64 sectors at LBA = 0x2a001bd2 = 704650194 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 1b 2a d2 e0 00 00:21:20.832 READ DMA EXT 25 00 00 00 40 00 00 00 1b 22 7a e0 00 00:21:20.826 READ DMA EXT 25 00 00 00 40 00 00 00 1b 1d b2 e0 00 00:21:20.824 READ DMA EXT 25 00 00 00 40 00 00 00 1b 32 3a e0 00 00:21:20.823 READ DMA EXT 25 00 00 00 40 00 00 00 1b 31 0a e0 00 00:21:20.822 READ DMA EXT Error 29679 [14] occurred at disk power-on lifetime: 7558 hours (314 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 19 66 00 89 08 e0 00 Error: UNC 256 sectors at LBA = 0x1966008908 = 109085493512 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 19 89 66 08 e0 00 00:49:17.821 READ DMA EXT 25 00 00 00 08 00 00 0c cd fc 38 e0 00 00:49:17.820 READ DMA EXT 25 00 00 00 80 00 00 14 4c 4b c8 e0 00 00:49:17.809 READ DMA EXT 35 00 00 00 08 00 00 10 fd 0a b8 e0 00 00:49:17.699 WRITE DMA EXT 25 00 00 00 08 00 00 00 63 1f e0 e0 00 00:49:17.600 READ DMA EXT Error 29678 [13] occurred at disk power-on lifetime: 7558 hours (314 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 19 a9 00 3c e0 e0 00 Error: UNC 256 sectors at LBA = 0x19a9003ce0 = 110209547488 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 19 3c a9 e0 e0 00 00:49:14.683 READ DMA EXT 25 00 00 01 00 00 00 19 3c a8 e0 e0 00 00:49:14.682 READ DMA EXT 25 00 00 01 00 00 00 19 3c a7 e0 e0 00 00:49:14.680 READ DMA EXT 25 00 00 01 00 00 00 19 3c a6 e0 e0 00 00:49:14.679 READ DMA EXT 25 00 00 01 00 00 00 19 3c a5 e0 e0 00 00:49:14.677 READ DMA EXT Error 29677 [12] occurred at disk power-on lifetime: 7558 hours (314 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 16 48 00 a1 a0 e0 00 Error: UNC 256 sectors at LBA = 0x164800a1a0 = 95697281440 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 16 a1 48 a0 e0 00 00:49:10.324 READ DMA EXT 25 00 00 01 00 00 00 16 a1 47 a0 e0 00 00:49:10.322 READ DMA EXT 25 00 00 01 00 00 00 16 a1 46 a0 e0 00 00:49:10.315 READ DMA EXT 25 00 00 00 80 00 00 14 4a 0b 98 e0 00 00:49:10.302 READ DMA EXT 25 00 00 00 40 00 00 00 22 cb 6a e0 00 00:49:10.288 READ DMA EXT Error 29676 [11] occurred at disk power-on lifetime: 7558 hours (314 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 19 a9 00 3c e0 e0 00 Error: UNC 256 sectors at LBA = 0x19a9003ce0 = 110209547488 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 19 3c a9 e0 e0 00 00:49:07.874 READ DMA EXT 25 00 00 01 00 00 00 19 3c a8 e0 e0 00 00:49:07.872 READ DMA EXT 25 00 00 01 00 00 00 19 3c a7 e0 e0 00 00:49:07.870 READ DMA EXT 25 00 00 01 00 00 00 19 3c a6 e0 e0 00 00:49:07.869 READ DMA EXT 25 00 00 01 00 00 00 19 3c a5 e0 e0 00 00:49:07.867 READ DMA EXT Error 29675 [10] occurred at disk power-on lifetime: 7557 hours (314 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 2a 00 1b ea e0 00 Error: UNC 64 sectors at LBA = 0x2a001bea = 704650218 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 1b 2a ea e0 00 00:21:54.970 READ DMA EXT 25 00 00 00 40 00 00 00 1b 22 c2 e0 00 00:21:54.962 READ DMA EXT 25 00 00 00 03 00 00 02 fb f7 c8 e0 00 00:21:54.921 READ DMA EXT 25 00 00 00 08 00 00 0c d5 01 50 e0 00 00:21:54.918 READ DMA EXT 25 00 00 00 08 00 00 0c d5 01 48 e0 00 00:21:54.912 READ DMA EXT Error 29674 [9] occurred at disk power-on lifetime: 7557 hours (314 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 2a 00 1b ba e0 00 Error: UNC 64 sectors at LBA = 0x2a001bba = 704650170 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 1b 2a ba e0 00 00:01:33.388 READ DMA EXT 25 00 00 00 40 00 00 00 18 bd 1a e0 00 00:01:33.387 READ DMA EXT 25 00 00 00 40 00 00 00 18 be 72 e0 00 00:01:33.385 READ DMA EXT 25 00 00 00 28 00 00 00 18 bc b2 e0 00 00:01:33.382 READ DMA EXT 25 00 00 00 48 00 00 00 1a 79 a8 e0 00 00:01:33.294 READ DMA EXT Error 29673 [8] occurred at disk power-on lifetime: 7557 hours (314 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 c9 00 35 c1 e0 00 Error: UNC 1 sectors at LBA = 0xc90035c1 = 3372234177 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 35 c9 c1 e0 00 00:00:49.789 READ DMA EXT 25 00 00 00 01 00 00 00 35 c9 c0 e0 00 00:00:49.788 READ DMA EXT 25 00 00 00 01 00 00 00 35 c9 bf e0 00 00:00:49.787 READ DMA EXT 25 00 00 00 01 00 00 00 35 c9 be e0 00 00:00:49.787 READ DMA EXT 25 00 00 00 01 00 00 00 35 c9 bd e0 00 00:00:49.786 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 44 Celsius Power Cycle Min/Max Temperature: 43/45 Celsius Lifetime Min/Max Temperature: 25/51 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (75) Index Estimated Time Temperature Celsius 76 2019-01-17 22:21 45 ************************** 77 2019-01-17 22:22 45 ************************** 78 2019-01-17 22:23 44 ************************* 79 2019-01-17 22:24 45 ************************** 80 2019-01-17 22:25 45 ************************** 81 2019-01-17 22:26 44 ************************* 82 2019-01-17 22:27 45 ************************** 83 2019-01-17 22:28 45 ************************** 84 2019-01-17 22:29 44 ************************* 85 2019-01-17 22:30 44 ************************* 86 2019-01-17 22:31 45 ************************** 87 2019-01-17 22:32 45 ************************** 88 2019-01-17 22:33 45 ************************** 89 2019-01-17 22:34 ? - 90 2019-01-17 22:35 45 ************************** 91 2019-01-17 22:36 44 ************************* ... ..( 9 skipped). .. ************************* 101 2019-01-17 22:46 44 ************************* 102 2019-01-17 22:47 43 ************************ 103 2019-01-17 22:48 44 ************************* ... ..( 99 skipped). .. ************************* 75 2019-01-18 00:28 44 ************************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 6854 Vendor specific